MTD 675 thru 689 - Manual (Page 2)

IMPORTANT
RULES FOR SAFE OPERATION
A
THIS SYMBOL POINTS OUT IMPORTANT SATETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER
THE PERSONAL SAFETY AND/OR PROPERTY DF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS
IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR POWER VACUUM. FAILURE TO COMPLY WITH THESE
INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. WHEN YOU SEE THIS SYMBOL— ^ HEED ITS WARNING.
A
Your power vacuum was built to be operated according to the rules for safe operation in this manuai.
DANGER:
As with any type of powi.>r equipment, careiessness or error on the part of the operator can resuit in
serious injury. If you viol: ite any of these rules, you may cause serious injury to yourseif or others.
Read this operating and service instruction manuei carefully.
Be thoroughly familiar with the controls and proper use of the
power vacuum.
Never allow children to operate this power vacuum.
Keep the area of operation clear of all persons, [ articulariy
small children and pets.
Check fuel before starting engine. Do not fill fuel tank indoors,
when engine is running, or while engine is hot. W pe off any
spilled fuel before starting engine.
Do not change engine governor settings.
Do not put hands near rotating parts for any reason.
If the power vacuum should start to vibrate abnormally, stop
the engine and check immediately for the cause. Vibration is
generally a warning of trouble.
Before cleaning, repairing or inspecting, make certa n all mov­
ing parts have come to a complete stop. Disconnect spark plug
wire and keep wire away from plug to prevent accid mtal start­
ing. Also keep throttle control lever in the stop positi )n.
If the power vacuum should become blocked with dr bris at any
point, shut engine off and wait until the impeller comes to a
complete stop before attempting to remove the obstruction.
Disconnect spark plug wire to prevent accidental stai ting.
10. Check all bolts for tightness at frequent periods.
11. Never store this power vacuum with fuel in the tank. Allow
engine to cool before storing in any enclosure.
Keep bag and equipment free of debris when not in use.
Never operate this power vacuum unless air duct and vacuum
bag are properly affixed in their place. Large zippered end of
bag must be closed when operating to prevent objects from
being blown out.
Never empty vacuum bag when engine is running.
Never change inlet nozzle or auxiliary hose attachment when
engine is running.
16. The manufacturer recommends that the operator wear safety
glasses or some other suitable eye protection when operating
this machine.
Check the vacuum bag frequently for wear and replace when
necessary.
Never operate as a leaf blower unless impeller guard and guard
assembly are properly affixed in their place.
Exercise caution whenever operating as a leaf blower. Do not
allow discharge to be pointed in the direction of persons.
No one should operate this unit while intoxicated or while tak­
ing medication that impairs the senses or reactions.
12.
13.
14.
15.
17.
18.
19.
20 .
CONTENTS OF HARDWARE PACK
(Hardware pack may contain extra items which are not used on your unit. Quantities of parts and part
numbers are shown in parentheses.)
ATTACHING THE NOZZLE AND
AIR DUCT ASSEMBLY
Hand Knobs
(Qty. 2)
(720-0170)
Cupped
Washers (Qty. 3)
■ (736-0242)
Flat
Washer (Qty. 1)'
(736-0231)
B ATTACHING THE
UPPER HANDLE
t
Hex Bolts 1/4-20 X
1-3/4" Long (Qty. 4)
(710-0136)
He c Lock Nuts
1A -20 Thread
(Qty. 4)
(712-0107)
m
(E
INSTALLING THE BAG
Stu d Pins (Qty. 2)
(711-0737)
Push-On
S peed Nuts
(Qty. 2)
(1539-019)
ATTACHING THE CLUTCH ROD
(Self-Propelled Units Only)
Clutch Grip and Extension^____.
Spring are Not Shown ( )
Clevis Pin
(Qty. 1)
(711-0679)-
Hairpin Clip
(Qty. 1)
(714-0145)
Hex Lock
Nut 1/4-20 Thread
(Qty. 1)
(712-0107)
Hex Jam Nut
1/4-20 Thread
(Qty. 1)
(712-0298)
(Thinner Nut)
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
FIGURE 1.
0
INCHES