MTD 217-300 - Manual (Page 3)

MODEL 217-350 and 217-300
Ulus.
No. Part
No.
DESCRIPTION
( ) - No. Required Per Assembly
Ulus.
No.
Part
No.
DESCRIPTION
( ) - No. Required Per Assembly
1 350-4330 Tailpiece Assembly 58 746-122 Control - Throttle (complete) Std. Handle
2 321-4102-1 Gear Case Assembly (Complete) 58 746-110 Control - Throttle (Plow Type Handle)
3 350-4134 Outer Tine Adapter Assembly 59 746-111 Cable Clip
4 350-4138 Inner Tine Adapter Assembly 60 742-107 Tine - L. H.
5 310-4168 Reverse Pivot Bracket Assembly 61 742-108 Tine - R. H.
6 310-4164 Control Handle Assembly 62 736-124 Dust Pad
7 321-4172 Wheel Hanger Assembly 63 736-125 Dust Pad
8 350-4170 Engine Mounting Plate 64 — Engine
9 310-4149 Belt Retainer 65 711-231 Clevis Pin
10 310-4151 Belt Retainer 66 714-106 Locking Pin
11 310-4158 Control Lever . 67 711-137 Support Pin
12 310-4148 Belt Clip 68 756tl04 Pulley
13 321-4162 Belt Guard 69 717-109 Reverse Drive Wheel
14 310-4155 Control Rod 70 748-;lll Bronze Sleeve Bearing
15 310-8271 Adjustment Tube 71 756-112 Pulley — 2 Stage
16 310-4147 Belt Clip 72 711-138 Shoulder Screw
17 350-4114 Rear Frame --73 756-108 Pulley — 2 Stage
18 350-4112 Side Frame — R. H. 74 710-765 Set Screw — Allen 5/16—24 x 1/4 Ig.
19 350-4113 Side Frame — L. H. (Not Shown)
20 312t4261 Dust Shield 75 710-185 Allen Socket Head Cap Screw 10—32x 1 Ig.*
21 310-4167 Adjustment Plate 76 732-958 Spring — Compression
22 312-4243 Handle Panel — Small — Std. Handle 77 736-147 Lockwasher #10 Screw *
22 350-4121 Handle Panel — Plow Type 78 736-300 Washer 3/8 I.D.*
23 310-4246 Handle - R. H. - Std. 79 736r466 Washer 17/32 I.D.*
23 310-4186 Handle — Plow Type — R. H. 80 710-122 Hex Hd. Cap Sew. 5/16—24 x 1 Ig.*
24 310-4247. Handle - L. H. - Std. 81 310-4101 Locking Clamp (Not Shown) t
24 310-4143 Handle — Plow Type — L. H. 82 721-100 Oil Seal - Garlock #76 x 6113 t
25 711-213 Control Rod 83 721-101 Oil Seal - Garlock #78 x 7510 t
26 321-4328 Depth Bar 84 719-100 Housing — Gear Case t
27 305-1166 Grip 85 719-lOlR Bearing Adjustment Cap - 1”
28 310-4124 Handle Mounting Bracket 86 719-102 Bearing Adjustment Cap - 3/4” t
29 ■ 501-4221 Wheel Assembly 87 748-106 Bronze Sleeve Bearing t
30 710-275 Hex Hd. Cap Sew. 1/2—13 x 5 Ig.* 88 737-108 Alemite Drive Fitting #1992-B1 * t
31 712-384 Hex Centerlock Nut 1/2—13 thd. * 89 711-132 Worm Shaft - 3/4” t
32 736-108 Washer 33/64 I.D.* 90 711-133 Tine Shaft - 1” t
33 732-376 Spring — Tension 91 717-104 Worm t
34 712-107 Hex Centerlock Nut 1/4—20 thd.* 92 717-105 Worm V/heel f
35 756-370 Idler Bearing Assembly 93 714-103 Key - Woodruff #91 * t
36 712-372 Hex Centerlock Nut 5/16—18 thd.* 94 711-130 Spacer - 3/4” t
37 714-314 Key - Hi Pro #606 95 711-131 Spacer-1” t
38 710-373 Shoulder Bolt 96 716-101 Snap Eiing - Tru Arc #5100-75 * t
39 712-430 Hex Elastic Stop Nut 3/8—16 thd. 97 716-102 Snap Ring - Tru Arc #5100-175 * t
40 712-123 Hex Nut 5/16-24 thd. * 98 737-102 Pipe F'lug - Special Breather Type t
41 736-463 Washer 9/32 I.D. * 99 737-103 Pipe F’lug - Square Head 3/8 thread * t
42 710-258 HexHd. CapSew. 1/4—20 x 5/8 Ig.* 100 735-100 "O” Ring 2-1/8
X
2-3/8
X
1/8 t
43 736-169 Lockwasher 3/8 Screw * 101 735-101 "O” Ring 3-5/8
X
3-7/8 x 1/8 t
44 712-798 Hex Nut 3/8-16 thd. * 102 714-474 Cotter Pin 1/8 Dia. x 3/4 Ig» * t
45 712-116 Hex Elastic Stop Nut 3/8 — 24 103 741-107 Roller Bearing - Timken 3/4” t
46 710-113 HexHd. Cap Sew. 3/8—24 x 1-5/8 Ig. 104 741-108 Roller Bearing - Timken 1” t
Heat Treated * 105 710-125 Rd. Hd. Mach. Sew. 10-24 x 1/2 Ig. * t
47 710-253 Hex Hd. Cap Sew. 3/8—16 x 1 Ig.
*
107 710-256 Carriage Bolt 1/4-20 x 1-1/2 Ig.
*
48 710-183 HexHd. Cap Sew. 3/8-16 x 1-1/8 Ig.* 108 312-4257 Handle Panel (Large) Std. Handle Only
49 710-451 Carriage Bolt 5/16-18 x 3/4 Ig.
*
109 710-252 HexHd. Cap Sew. 1/4—20 x 3/4 Ig.
*
50 736-119 Lockwasher 5/16 Screw
*
110 712-324 Hex Stop Nut 1/4—20 thread
*
51 710-442 HexHd. Cap Sew. 5/16-18 x 1-1/2 Ig.
*
111 350-4160 Control Mtg. Brkt.-Plow Type Handle
52 712-267 Hex Nut 5/16-18 thd.* 901-4287 Inner Tine Ass’y
-
L.H.-Complete
53 710-118 HexHd. Cap Sew. 5/16-18 x 3/4 Ig.* 901-4288 Inner Tine Ass^y-R.H.
•*
Complete
54 710-136 HexHd. Cap Sew. 1/4-20 x 1-3/4 Ig.
*
901-4289 Outer Tine Ass'y-L.H.-Complete
55 714-105 Key
-
Square 3/16 x 3/16 x 1 Ig.* 901-4290 Outer Tine Ass’y-R.H.-Complete
56 754-104 “V” Belt 1/2
X
32 - Gates *
727-112 Lubricant 5 oz. (Gear Case)
57 754-103 “V” Belt 1/2
X
27 - Gates *
* For faster service obtain standard nuts, bolts and washers locally.
part number and size as shown on parts list,
t Part of Gear Case Assembly (Complete) 321r4102-l.
If these items cannot be obtained locally, order by
FORM NO. 770-9 12C