beautypg.com

Assembly, Computed kickback angle {cka table, Warning – Poulan 1975 User Manual

Page 6

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

background image

Computed kickback angle {CKA

Table

MODEL

BAR

CHAIN P/N

CKA without chain brake

P/N

Length

1Э50/1Э75/

2050/2050WT

952044363

14"

Э5205120Э

24=

2055/2075/

2150/2150PR

952044370

16”

952051211

19=

2155/2175/

2350/2375

952044418

IS"

952051333

14=

NOTE:

If tfiìs saw is to be used for com­

mercial logging, a chain brake is required
and shall not be removed or otherwise dis­
abled to comply with Federal OSHA Regula­

tions for Commercial Logging.

^WARNING:

The engine exhaust

from this product contains chemicais known
to the State of California to cause cancer,

birth defects or other reproductive harm.

SAFETY NOTICE:

Exposure to vibrations

through prolonged use of gasoline powered

hand tools could cause blood vessel or nerve
damage In the fingers, hands, and joints of
people prone to circulation disorders or
abnormal swellings. Prolonged use in cold

weather has been linked to blood vessel

damage in otherwise healthy people. If
symptoms occur such as numbness, pain,
loss of strength, change in skin color or texture,
or loss of feeling in the fingers, hands, or joints,
discontinue the use of this too! and seek
medicai attention. An anti-vibration system
does not guarantee the avoidance of tìiese
problems. Users who operate power toots on
a contìnua! and regular basis must monitor
closely frieir physical condition and the
condition of this toot.

SPECIAL NOTICE:

Your saw is equipped

with a temperature limiting muffler and spark

arresting

screen

which

meets

the

requirements of California Codes 4442 and
4443. Ail U.S. forest land and the states of
California, Idaho, Maine, Minnesota, New

Jersey, Oregon, and Washington require by

law that many interni combustion engines to
be equipped with a spark arresting screen, if
you operate a chain saw in a state or locale

where such regulations exist, you are legally

responsible for maintaining the operating
condition of these parts. Failure to do so is a

violation of the law. Refer to frie SERVICE

section for maintenance of the spark arresting
screen. Failure to follow all Safety Rules and

Precautions can result in serious injury. If

situations occur which are not covered in this
manual, use care and good judgement. If you
need assistance, contact your authorized
service dealer or cali 1 -800-554-6723.

STANDARDS:

This saw is listed by Under­

writer's Laboratories, ino., in accordance witii:
ANSI

B175.1-2000

American

National

Standards for Gasoline-Powered Chain
Saws - Safety Requirements
CSA Z62.1-03 Chain Saws - Occupational

Health and Safety

CSA Z62.3-96 Chain Saw Kickback Occu­
pational Health and Safety

ASSEMBLY

Protective gloves (not provided) should be

worn during assembly.

ATTACHING THE BAH & CHAIN

(If not

already attached)

WARNING:

if received assembled,

repeat al steps to ensure your saw is properly

assembled and all fasteners a'e secure. Al­
ways wear gloves when handling the chain.
The chain is sharp and can cut you even when

it is not moving!

1- Loosen and remove the chain brake

nuts and the chain brake from the saw.

2.

Remove the piastic shipping spacer (if

present).

Location of shipping spacer

Bar Tool

An adjusting pin and screw is used to ad­
just the tension of the chain. It is very im-

poriani when assembSng the bar, that the
pin located on the adjusting screw aligns
into a hole in the bar. Turning the screw will
move the adjustment pin up and down the

screw. Locate this adjustment before you

begin mounting the bar onto the saw. See
iltustration below.

fnside view of
Chain Brake

Adjustment located on Chain Brake

4- Turn the adjusting screw by hand coun­

terclockwise until the adjusting pin just
touches the stop. This should allow the

pin to be near the correct position.

5. Siide guide bar behind ciutch drum until

guide bar stops against clutch drum
sprocket.

This manual is related to the following products: