MTD 219-100 - Manual (Page 3)

"V'
TILLER MODEL 219-100
Ulus
No.
Part
No.
Descripti on
( )- No. req'd. per Assy.
Ulus.
No.
Part
No.
Description
( )-No. req’d. per Assy.
Illus.
No.
Part
No.
Description ^
()-No. req’d per Assy.
1 351-4105 Mounting Plate Assembly 41 710-373 Shoulder Bolt 79 719-102 Bearing Adjustment Cap 3/4" ••
2 321-4100 Gear Case Assembly (complete) 42 736-300 Washer 3/8 I. D. * 80 719-lOlR Bearing Adjustment Cap 1" **
3 351-4329 Tailpiece Assembly 43 712-430 Hex Elastic Stop Nut 3/8 - 16 thd. 81 748-106 Bronze Sleeve Bearing **
4 321-4134 Outer Tine Adapter Assembly 44 736-169 Lockwasher 3/8 Screw * 82 737-108 Alemite Drive Fitting-#1992-B1* **
5 321-4138 Inner Tine Adapter Assembly 45 712-798 Hex Nut 3/8 - 16 thd. * 83 TH-132 Worm Shaft 3/4" •*
6 310-4164 Control Handle Assembly 46 712-116 Hex Elastic Stop Nut 3/8-24 thd. 84 711-133 Tine Shaft 1" **
7 312-4187 Idler Bracket Assembly 47 710-113 Hex Hd. Cap Sew. 3/8-24 x 1-5/8 Lg. * 85 717-104 Worm **
8 312-4244 Handle - R. H. 48 710-253 Hex Hd. Cap Sew, 3/8-16x1 Lg. * 86 717-105 Worm Wheel **
9 312-4245 Handle - L. H. 49 710-183 Hex Hd, Cap Sew. 3/8-16 x 1-1/8 Lg. * 87 714-314 Key - Hi Pro #606 * **
10 351-4110 Leg - R. H. 50 710-451 Carriage Bolt 5/16-18x3/4 Lg, * 88 714-103 Key - Woodruff #91 * **
11 351-4109 Leg - L.H. 51 736-119 Lockwasher 5/16 Screw * 89 711-130 Spacer 3/4" *•
12 321-4328 Depth Bar 52 712-123 Hex Nut 5/16 - 24 thd, * 90 711-131 Spacer 1" ••
13 351-4243 Handle Panel Engine Mounting Nut - not shown 91 716-101 Snap Ring - TruArc #5100-75 **
14 310-4126 Inspection Plate 53 710-158 Hex Hd. Cap Sew. 5/16-24x1-1/4 lg. * 92 716-102 Snap Ring - TruArc #5100-100 **
15 310-4156 Control Lever Engine Mounting Bolt - not shown 93 737-102 Pipe Plug - Special Breather Type **
16 312-4161 Belt Guard 54 712-267 Hex Nut 5/16 - 18 thd. * 94 737-103 Pipe Plug-Square Hd. 3/8 thd.** *
17 310-4152 Control Rod - lower 55 710-118 Hex Hd. Cap Sew. 5/16 - 18 x 3/4 Lg, * 95 735-100 ”0” Ring 2-1/8 X 2-3/8 X 1/8 **
19 711-393 Control Rod - upper 56 710-606 Hex Hd. Cap Sew, 1/4-26x 1-1/2Lg.* 96 735-101 "0" Ring 3-5/8 X 3-7/8 X 1/8 •*
20 312-4103 Engine Bed 58 714-105 Key-Sq. 3A6x 3/16x1 * 97 714-474 Cotter Pin 1/8
21 310-7439 Anchor Spring Pin 59 756-107 Pulley 2-1/2 X 7/8 98 741-107 Roller Bearing - Timken 3/4
22 305-1166 Grip 60 710-765 Set Sew. - Allen 5/16 - 24x 1/4 Lg. * 99 741-108 Roller Bearing - Timken 1" **
23 310-7353 Belt Clip 61 754-103 " V " Belt 1/2x27 - Gates * 100 736-147 Lockwasher #10 Screw * **
24 310-4124 Handle Mounting Bracket 62 710-202 Hex Hd.Self-tapping Sew, 10-32xl/2Lg. 101 310-8271 Adjustment Tube
25 310-4195 Belt Clip 63 736-147 Lockwasher #10 Screw * 102 710-252 Hex Hd, Cap Sew. l/4-20x3/4Lg. *
26 501-8009 Wheel Assembly 64 746-J7J -Control - Throttle (complete) 103 712-324 Hex Elastic Stop Nut 1/4 - 20 thd. *
27 710-259 Hex Hd. Cap Sew. 5/16-18x5/8 Lg. • 65 742-105 Tine - L.H. 104 711-414 Control Rod
28 732-194 Spring Pin 66 742-106 Tine R. H. 105 711-392 Ferrule
29 711-231 Clevis Pin 67 746-111 Cable Clip 106 310-4392 Handle Rod Assembly
30 Engine 68 736-124 Dust Pad 107 351-4381 Handle Assembly
31 710-182 Hex Hd. Cap Sew. 1/2-13x3 Lg. • 69 736-125 Dust Pad 108 736-155 Rubber Washer
32 712-384 Hex Centerlock Nut 1/2-13 thd. * 70 732-958 Spring - Compression 109 720-143 Knob
33 736-108 Washer 33/64 I. D. * 71 710-136 Hex Hd. Cap Sew. 1/4-20x 1-3/4 Lg.* no 351-4386 Brackets - Panel
34 732-376 Spring - Tension 72 710-256 Carriage Bolt 1/4-20x1-1/2 Lg. * 111 736-204 Flat Washer
35 712-107 Hex Centerlock Nut 1/4-20 thd. * 73 736-463 Washer 9/32 I.D. * 112 714-507 Cotter Pin 3/32x3/4 Lg. *
36 756-370 Idler Bearing Assembly 74 305-7891 Ball Knob + 113 714-115 Cotter Pin 1/8x1 Lg. *
37 712-372 Hex Centerlock Nut 5/16 - 18 thd. * 75 310-4101 Locking Clamp ** 114 712-798 Hex Nut 3/8 - 16 thd. *
38 756-926 Pulley 4-1/2 X 3/4 76 721-100 Oil Seal - Garlock #76x6113 ** 115 710-253 Hex Hd. Cap Sew. 3/8 - 16x1 Lg.*
39 710-125 Rd. Hd. Mach. Sew. 10-24x 1/2 lg.* 77 721-101 Oil Seal - Garlock #78x7510 ** 116 710-106 Hex Hd. Cap Sew. 1/4 - 2-x l-l/4Lg. *
40 710-421 Set Sew. Allen 5/16 - 18x 1/4 Lg.'* 78 719-100 Housing - Gear Case ** 117 736-195 Flat Washer
o
31
3
z
o
» *
For faster service, obtain standard nuts, bolts, and washers locally. If these items
cannot be obtained locally, order by part number and size as shown on parts list.
Part of Gear Case Assembly (complete) 394-4100.
Part of Control Handle Assembly 310-4164.
321-4100 Gear Case Assembly (complete)
901-4291 Tine Assembly, complete - L.H. Inner
901-4292 Tina^ssembly, complete - R. H. Inner
901-4293 Tine Assembly, complete - L.H. Outer
901-4294 Tine Assembly, complete - R. H. Outer
727-112 Mobilube SAE 140 - 502