To set the time, Using the alarm, To illuminate the display – Casio TMR-200 User Manual
Page 2: Battery replacement, User’s guide tmr-200
USER’S GUIDE TMR-200
2
TO SET THE TIME
1. Press the
SET button (6
6
6
6
6)
to cycle through the setting screens as shown below.
2. Select the setting you want to change, and then use the
HR/MONTH button (2
2
2
2
2)
,
MIN/DATE button
(3
3
3
3
3)
, and
YEAR/5-AL ON/OFF button (4
4
4
4
4)
to change it.
•
Holding down any button changes its setting at high speed.
•
You can set the year in the range of 2000 to 2039. The day of the week is set automatically in
accordance with the date setting.
•
Pressing
HR (2
2
2
2
2)
or
MIN (3
3
3
3
3)
while the Time Setting Screen is on the display causes the seconds
count to be reset to 00.
3. After configuring the settings you want, use the
SET button (6
6
6
6
6)
to display the Normal Timekeeping
Screen.
•
The clock automatically returns to the Normal Timekeeping Screen if you leave a setting screen on
the display for about three minutes without performing any operation.
USING THE ALARM
•
This clock has a Daily Alarm and a 5 Reminder Alarms. The following table summarizes the features of
each alarm type.
Time Setting Screen
Date Setting Screen
Normal Timekeeping Screen
Alarm Type
Daily Alarm
5 Reminder
Alarms
SNOOZE Alarm
Yes
No
Alert Duration
1 minute (repeats 7 times
every five minutes)
30 seconds
For this type of alert:
Beep
Vibration
Beep + Vibration
Select this setting:
BEEP
VIB
BEEP&VIB
Which is indicated by the display indicator:
•
For the alarm alert, you can set up the clock to use an audible beeper or a silent vibrator, or the beeper
and vibrator in combination.
•
When an alarm is set and turned on, it performs the specified alert operation each day at the specified
time. Pressing any clock button stops an ongoing alert operation.
•
Note that the Daily Alarm is a snooze alarm. This means that the alert operation is repeated about five
minutes after you stop it. To completely stop the Daily Alarm so it does not sound again, slide the
Alarm
Mode selector (8
8
8
8
8)
to OFF.
To set the Daily Alarm time
1. Slide the
Alarm Mode selector (8
8
8
8
8)
to SET. This causes the current daily alarm time setting to flash on
the display.
2. Press
HR (2
2
2
2
2)
to increase the hour setting and
MIN (3
3
3
3
3)
to increase the minute setting. Holding down
either button changes its setting at high speed.
3. After you set the alarm time, slide the
Alarm Mode selector (8
8
8
8
8)
to OFF or ON.
•
An alarm does not sound if its alarm time is reached while an alarm setting screen is on the display.
To turn the Daily Alarm on and off
Slide the
Alarm Mode selector (8
8
8
8
8)
to ON to turn the Daily Alarm on, or OFF to turn it off.
•
Turning on the Daily Alarm causes the
indicator to appear at the bottom of the display. Also, the
Daily Alarm time setting appears in the upper part of the display in place of the current date. While the
Daily Alarm is turned on, you can view the current month and day by holding down the
HR/MONTH
button (2
2
2
2
2)
,
MIN/DATE button (3
3
3
3
3)
, or
YEAR/5-AL ON/OFF button (4
4
4
4
4)
.
To set the 5 Reminder Alarms
1. Press the
5-AL.SET button (5
5
5
5
5)
until the setting of Reminder Alarm
(
)
starts to flash.
•
This causes the setting of Reminder Alarm
(
)
to flash.
2. Press
HR (2
2
2
2
2)
to increase the hour setting and
MIN (3
3
3
3
3)
to increase the minute settings. Holding down
either button changes its setting at high speed.
3. Press the
5-AL.SET button (5
5
5
5
5)
to move the flashing to the next Reminder Alarm
(
)
.
•
This causes the setting of the next Reminder Alarm to flash.
4. Repeat steps 2 and 3 to set the other Reminder Alarm times.
5. When Reminder Alarm
(
)
is flashing, press the
5-AL.SET button (5
5
5
5
5)
to return to the Normal
Timekeeping Screen.
To turn the 5 Reminder Alarms On and Off
1. Press the
5-AL.SET button (5
5
5
5
5)
until the setting of Reminder Alarm
(
)
starts to flash.
•
This causes the setting of Reminder Alarm
(
)
to flash.
2. Press the
5-AL.SET button (5
5
5
5
5)
to move the flashing to the Reminder Alarm you want to turn on or off.
3. Press the
5-AL ON/OFF button (4
4
4
4
4)
to toggle the flashing alarm on (current alarm time setting
displayed) and off (–:– – displayed).
4. When Reminder Alarm
(
)
is flashing, press the
5-AL.SET button (5
5
5
5
5)
to return to the Normal
Timekeeping Screen.
Selecting the Alert Mode
•
Use the
Alert Mode selector (9
9
9
9
9)
to select the alert mode you want to use for the Daily Alarm and for
all of the 5 Reminder Alarms.
TO ILLUMINATE THE DISPLAY
Press
SNOOZE/LIGHT button (1
1
1
1
1)
to illuminate the display for about three seconds.
Important!
•
Overuse of the light can shorten battery life.
BATTERY REPLACEMENT
Replace batteries whenever the display of the clock becomes dim and difficult to read.
1. Open the battery compartment cover as shown in the illustration.
2. Remove both old batteries.
3. Load new batteries. Make sure that their positive (+) and negative (–) ends face in the correct
directions. If you load batteries incorrectly, they can burst and damage the clock.
4. Replace the battery compartment cover.
5. Press the
RESET button (7
7
7
7
7)
. Be sure to press the
RESET button (7
7
7
7
7)
after replacing batteries.
Battery precautions
•
Keep batteries out of the reach of small children. If a battery is accidentally swallowed, contact your
physician immediately.
•
Be sure to load the batteries with their positive (+) and negative (–) ends facing correctly.
•
Never mix old and new batteries, or batteries of different brands.
•
Never charge the batteries that come with the clock.
•
Should batteries ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get
onto your skin.
•
Replace the batteries at least once a year, even if the current batteries are working properly.
•
The batteries that come with the clock lose some of their power during transport and storage.