Traxxas 59076-1 - Manual (Page 21)

SLAYER PRO 4X4 • 21
• Slightly lean fuel mixtures deliver
stronger, more efficient
combustion and more power, but with
less lubrication.
• Slightly rich fuel mixtures deliver
cooler running and more
lubrication but with slightly less power.
Tuning the engine means finding the
perfect balance between the two;
excellent power to meet your needs
while maintaining good lubrication
for long engine life. The optimal fuel
mixture setting is rich to provide a
safety margin against having a lean
condition if some variable changes (such
as the temperature from one day to the
next).
General fuel mixture settings are
measured by the number of turns
the needles are turned out from fully
closed. The fuel mixture settings have been pre-set from the factory
to typical break-in settings. Do not readjust your carburetor from the
factory settings until after the engine is started and running, and you
have been able to observe the engine running to assess what minor
adjustments may be required to compensate for fuel, temperature,
and altitude. Adjustments are usually made in 1/8 or 1/16-turn
increments. If the engine sticks at top dead center (TDC), see page 35
for instructions on freeing the engine.
The Idle Speed Adjustment
The idle speed adjustment screw controls the closed position of the
throttle slide. When the throttle servo is in its neutral position, the
throttle slide should be stopped against the idle speed adjustment
screw. Always use the idle
speed adjustment screw
to control engine idle. See
page 27 for instructions on
adjusting the idle speed.
THE TRAXXAS EZ-START
ELECTRIC STARTING SYSTEM
The Traxxas EZ-Start brings the convenience of push-button electric
engine starting to your model. The EZ-Start consists of a hand-held control
unit and an on-board motorized starter.
• Power for the EZ-Start system comes from a 7.2-volt rechargeable
battery pack installed in the hand-held control unit.
• The engine glow plug is heated automatically by the EZ-Start system,
eliminating the need to keep up with a separate glow plug igniter.
• The voltage to the glow plug is kept constant, regardless of the load
placed on the starter by the starter motor.
• The “Glow Plug” LED (light emitting diode) on the control unit
indicates the condition of the glow plug.
• The “Motor” LED indicates the status of the EZ-Start electric starter motor.
• The cush drive mechanism in the drive unit prevents damage to the
gears caused by engine kickback.
• Smart Start ™ protection circuitry prevents damage to the motor by cutting
power if the load on the motor or other electronics exceeds safe limits.
Charging the EZ-Start Battery
The included charger can be used to charge the included EZ-Start
battery pack.
Do not charge batteries inside of an automobile. Read the
Safety Precautions section of this guide.
1. Plug the charger into a 12-volt automotive auxiliary power socket.
The charger is compatible with 12-volt automotive auxiliary power
sockets only. The LED on the charger will glow red to indicate it is
ready to charge a battery.
2. Connect the battery to begin charging. Plug the battery into the
charger. The charger’s LED will flash green, indicating that charging
has begun. The flashing green LED on the charger indicates the
charge progress.
3. Disconnect the battery when charging is complete. When the
battery is fully charged, the LED will light solid green. The battery
will be warm in your hand. Disconnect the battery.
Lean
Rich
See Tuning Your TRX 3.3
Racing Engine on page 25
for complete information on
adjusting the air/fuel mixture
and idle speed.
Factory Needle Settings
If your factory preset
carburetor adjustments have
been tampered with, use the
following settings:
• Set the high-speed needle to
4 turns out from closed.
• Set the low-speed needle so
the screw head (red in Fig. A)
is flush (even) with the end
of the slide (yellow in Fig. A).
Always use the factory
settings for initial starting.
Only use these settings when
the factory settings have
been lost.
Higher nitro requires a richer
fuel mixture. When running
33% fuel, richen your high
speed needle 3/4 turn if
previously running 20% nitro
and then re-tune the engine
for maximum performance.
Low Speed
Needle Adjustment
Fig. A
THE TRX 3.3 RACING ENGINE
2
CHARGE PROGRESS
x1 1 green flash 0 - 25% charged
x2 2 green flashes 25% - 50% charged
x3 3 green flashes 50% - 75% charged
x4 4 green flashes 75% or more charged
Solid green LED 100% charged
CHARGER LED INDICATION MEANING
Solid Red LED Ready for Charging
Slowly Flashing Green LED Charging (see Charge Progress chart)
Solid Green LED Battery Fully Charged
Flashing Red LED Charger error
Note: If there is a problem with the battery, such as a short circuit, the charger’s LED will flash
red. Disconnect the battery and unplug the charger from its power source to clear the error.
Determine the cause of the error before continuing.