beautypg.com

Soundmatters SUBstageWall Bracket User Manual

Page 4

background image

Read this before you begin

IMPORTANT: Because the SUBstage generates a tremendous
amount of low-frequency energy, this bracket assembly MUST
be screwed solidly into wooden studs. It is NOT sufficient
to screw into metal studs, nor only into plaster or drywall.
(Obviously, screwing through the wall surface and into studs
is the right thing.) Using butterfly-style or other anchors in
drywall will NOT keep the bracket secure for long, and are most
definitely NOT suitable. The bottom line: use this bracket ONLY if
you can screw into wooden studs.

Read through all the instructions and look at the illustrations
before you begin. Having a good overview will make the
project proceed more smoothly and the final installation will be
professional quality.

Contents

1 Upper Bracket
1 Lower Bracket with attached Rubber Bushings
4 Bolts 1/4-20 x 3/8”
4 Washers 3/16”
1 J-hook (left side)
1 J-hook (right side)
4 Deck Screws (8 ga x 3”)
1 Instruction Sheet
1 Template Sheet

Tools needed

• Stud finder (do NOT attempt to install this bracket if it cannot be

securely attached to wooden studs with two screws per bracket)

• Drill and drill bit (1/8” or smaller for pilot holes)
• Phillips screwdriver
• 11mm (preferred) or 7/16” open-end wrench
• Level
• Pencil and tape

SUBstage 250/100 Wall-Mount Instructions for SSWB1 Mounting Bracket Kit

A. Mount Hardware on Substage

1. Unscrew and remove the four feet.

2. In their places: on top, screw in bolt and washer (leave loose

with about 3/16” space); then, on bottom, screw in bolt,
washer and J-hook (tighten firmly).

B. Align Template on Wall

1. Use stud finder. Carefully find centers of

appropriate studs, then lightly mark posi-
tion on wall in pencil. (Typically, studs in
residences are on 16” centers. The outer-
most holes on the wall-mountbrackets are
exactly 16” apart. What a coincidence!)

2. Tape template to wall at the

desired mounting height,
carefully aligning two top
holes and two bottom holes
with the centers of studs.
Be sure template diagram
is level. Use vertical dashed
lines to align template to
centerline of studs.

3. Drill a thin pilot hole (1/16”–1/8” dia) through the upper left

position. If drill successfully hits wood stud, proceed to drill

lower left. Drill each hole into wood about 1 “.

4. Now go to upper right position and drill pilot hole there that

will hit a stud. If successful, proceed to lower right pilot hole.

Drill each hole into wood about 1 “.

5. Remove template from wall.

C. Mount Brackets To Wall

1. Using the pilot holes you

drilled, mount brackets using

the deck screws provided. At

least 2” of screw thread should

enter the wood of the stud.

Tighten firmly, but do not over-

tighten.

D. Plug In Cables, Make Settings,

Give It a Test Listen, Tweak

1. Securely plug-in source interconnect and right-angle AC cord.

Turn on power switch because it may be difficult to get to it

once unit is mounted on the wall. (It’s always okay to leave

the unit powered on all the time.) Make sure your settings are

where you want them before you proceed to next step.

Pro tuning tip: Listen and tweak the settings for crossover, volume and phase

BEFORE final wall-mounting. Use the foam end caps from the packaging to

temporarily wedge the unit into approximate position

behind a chair or sofa. Note, once unit is wall-mounted,

it will have to be UN-mounted to change these settings

E. Hang It, then Secure It

1. Make sure the cables are routed down the back and will align

with the cutouts in the brackets

2. See the illustrations below. To “hang” the SUBstage on the

brackets, hold the unit about an inch directly above the

brackets, then move it straight down so the lower J-hooks

catch on the rubber-bushing-covered lower lip, and simul-

taneously the two upper bolts slip into the slots of the upper

bracket. The washers should be between the bolt heads and

the bracket.

Use a stud finder to find the studs, then use vertical

lines on template to carefully align holes with studs.

Move unit directly over the wall

brackets, then slide down into place

On top: Bolt slips into

slot on bracket.

On bottom: J-hook

should catch on lip.

Final step: firmly tighten both

top bolts using 11mm or 7/16”

open-end wrench

soundmatters international

tel: 775 981.1460

fax: 775 981.1465

www.soundmatters.com

3. When you are sure you’ve gotten it properly and securely

located (that is, both J-hooks on botton rail and both top

bolts completely inserted in their notches), use an 11mm

(or 7/16”) open-end wrench to tighten the top bolts

until tight. (As you are facing the SUBstage, tighten them

counterclockwise)

4. Ta-da, congratulations! Time to enjoy the fruits of your labor.

Plug in source interconnect, plug in AC, get down, get funky,

get low…enjoy that acoustic rubdown!

NOTE: When mounted correctly, there will be no rattles or

buzzes coming from the SUBstage, even at full throttle. BUT,

keep in mind that the powerful subwoofer is now mechanically

coupled to your wall. While this increases the amount of bass in

the room (a wonderful thing!), it may cause other things on

the wall to vibrate (say, picture frames, for example). If so,

secure them to the wall.