Casio CELVIANO AP45ES1C - Manual (Page 48)

A-6
MIDI Data Format
430A-E-090A
p
p
.......
P
rogram Number = 00H to 7FH
Send
Pr
ogram Change messages ar
e sent when you select a tone on
the instr
ument.
Pitch Bend Change
★
Format
Byte 1
Byte 2
CnH
ppH
n
.........
V
oice Channel Number = 0H to FH (Ch1 to Ch16)
ll
.........
Pitch Bend Change LSB = 00H to 7FH
m
m
....
Pitch Bend Change MSB = 00H to 7FH
Byte 1
Byte 2
B
yte 3
EnH
llH
mmH
Filter Cut Off Frequency
NRPN MSB = 01H NRPN LSB = 20H Data Entry MSB = mmH m
m
....
Filter Cut Of
f Fr
equency = 00H to 40H to 7FH (-64 to 0 to
+63)
Recognition
When the instr
ument r
eceives this message, the pr
eset Filter Cut
of
f Fr
equency value for the tone is changed to the value that
corresponds to the data entry MSB of the r
eceived message. Ther
e
is no change when the value of the data entry MSB is 40H(0).
Filter Resonance
NRPN MSB = 01H NRPN LSB = 21H Data Entry MSB = mmH m
m
....
Resonance= 00H to 40H to 7FH (-64 to 0 to +63)
Recognition
When the instrument r
eceives this message, the pr
eset Filter
Resonance value for the tone is changed to the value that corresponds to the data entry MSB of the r
eceived message. Ther
e
is no change when the value of the data entry MSB is 40H(0).
Filter/AMP
Envelope
Attack T
ime
NRPN MSB = 01H NRPN LSB = 63H Data Entry MSB = mmH m
m
....
Filter/AMP
Envelope
Attack T
ime = 00H to 40H to 7FH
(-64 to 0 to +63)
Recognition
When the instr
ument r
eceives this message, the pr
eset Filter/
AMP
Envelope
Attack T
ime value for the tone is changed to the
value that corr
esponds to the data entry MSB of the r
eceived
message. There is no change when the value of the data entry MSB is 40H(0).
Filter/AMP
Envelope Decay T
ime
NRPN MSB = 01H NRPN LSB = 64H Data Entry MSB = mmH m
m
....
Filter/AMP
Envelope Decay T
ime = 00H to 40H to 7FH
(-64 to 0 to +63)
Recognition
When the instr
ument r
eceives this message, the pr
eset Filter/
AMP
Envelope Decay T
ime value for the tone is changed to the
value that corr
esponds to the data entry MSB of the r
eceived
message. There is no change when the value of the data entry MSB is 40H(0).
Filter/AMP
Envelope Release T
ime
NRPN MSB = 01H NRPN LSB = 66H Data Entry MSB = mmH m
m
....
Filter/AMP
Envelope Release T
ime = 00H to 40H to 7FH
(-64 to 0 to +63)
Recognition
When the instr
ument r
eceives this message, the pr
eset Filter/
AMP
Envelope Release T
ime value for the tone is changed to the
value that corresponds to the data entry MSB of the r
eceived
message. Ther
e is no change when the value of the data entry
MSB is 40H(0).
RPN (Registered Parameter Numbers) Format
Byte 1
Byte 2
Byte 3
BnH
65H
qmH (MSB)
BnH
64H
qlH (LSB)
n
..........
V
oice Channel Number = 0H to FH (Ch1 to Ch16)
q
m
.......
M
S
B
o
f R
P
N
q
l
.........
LSB of RPN
Recognition
•
RPN messages not defined by the instr
ument can also be
received, but subsequent data entry values after undefined RPN messages ar
e ignor
ed.
•
After the MSB and LSB of an RPN ar
e r
eceived and the
applicable contr
ol parameters settings ar
e made, the value is
set by r
eceipt of the MSB of the subsequent data entry
. The
data entry LSB is ignor
ed.
Send
An RPN is sent whenever an operation that changes the parameter assigned to the RPN is performed.
Pitch Bend Sensitivity
★
RPN MSB = 00H RPN LSB = 00H Data Entry MSB = mmH m
m
....
Pitch Bend Sensitivity = 00H to 18H (0 to 24 semitones)
Recognition
The data entry LSB is always ignor
ed.
Master Fine T
uning
RPN MSB = 00H RPN LSB = 01H Data Entry MSB = mmH Data Entry LSB = llH m
m
l
l
....
M
aster Fine T
uning = 00 00H to 40H 00H to 7FH 7FH (-
100 to 0 to +99.99 cents)
Master Coarse T
uning
RPN MSB = 00H RPN LSB = 02H Data Entry MSB = mmH m
m
....
M
aster Coarse T
uning = 28H to 40H to 58H (-24 to 0 to
+24 semitones)
Recognition
The data entry LSB is always ignor
ed.
RPN Null
RPN MSB = 7FH RPN LSB = 7FH
Recognition
Once an RPN Null is sent, all r
eceived data entry MSBs and LSBs
are ignor
ed until another RPN message other than RPN Null or
an NRPN message is r
eceived.
Program Change
Format Recognition
•
The value llH mmH is 00H 00H at the lowest pitch, 00H 40H at mid-pitch, and 7FH 7FH at the highest pitch.
•
Y
ou have to set both the LSB and MSB together to form a 14-
bit value and make a Pitch Bend Change message r
ecognized
by the instr
ument.