Philips AZ2710-17 - Manual (Page 7)

- Place the set on a hard, flat surface so that it does not tilt.
- Do not ejippse the set CDs, batteries or cassettes to humidity, rain,
sand, direct sunlight or other places where high temperatures can
occur, such 8$ in the vicinity of heating apparatus or in motor cars
parked in the sun.
- Do not cover the set. The amplifier produces heat which must dis­
sipate freely, so make sure that there is sufficient ventilation around
the set. A minimum gap of 15 cm is necessary.
- The mechanical parts of the CD player and the cassette deck contain
self-lubricating bearings and must not be oiled or lubricated.
- A chamois leather slightly moistened with water is sufficient for
cleaning.the housing. Oo not use cleaning agents containing alcohol,
spirits, amnwhia or abrasives as these may harm the housing.
The lens of the CD player should never be touched.
The lens may cloud over if the CD player is moved from cold to warm
surroundings. The CD player will not start. Give the player some time
to^climatise.
To take a CD out of its box, press the center spindle while lifting the
CD. Always pick up the CO ^ the edge and replace the CD back in Its
box after use to avoid scratching and dust.
To clean the CO, wipe in a straight line from the centre towards the
edge using a soft, lint-free cloth. Do not use cleaning agents as they
may damage the disc.
Never write on a CD or attach stickers to it.
mmmimnmmn
To ensure a good recording and playback quality, clean the indicated
parts after every 50 hours of operation or, on average,
once a month. Use a cotton bud slightly moistened with alcohol or a
special head cleaning fluid.
• Press PLAY ► and clean die rubber pressure rollers ©.
• Then press PAUSE M and clean the capstans ( b ) and the heads ®.
• After cleaning, press ST0P«0PEN ■ 4.
Cleaning of the heads can also be done by playing a cleaning
cassette through once.
The type plate is located on the base of the set.
■ Í - ■ .
la fault occurs, first check the points listed below before taking the set for repair.
!7tf you are unable to remedy a problem by following these hints, consult your dealer or service center.
IWARNING
; Under no circumstances should you try to repair the set yourself, as this would invalidate the
iwarranty.
^PROBLEM _____ Severe radio hum or noise _____
- - POSSIBLE CAUSE
REMEDY
Set does not react to operation of
anyofthecontroit ___________________
- Electrostatic discharge.
♦ Switch off the set. disconnect the power plug,
reconnect after a few seconds.
¡Otsplay does act function property___________
!•- Electrostatic discharge.
Switch off the set, disconnect the mains plug and
reconnect after a few seconds.
> - Set runs on batteries.
• Switch to mains supply.
No sound
- VOLUME Is not adjusted.
• Adjust the VOLUME.
“ Headphones are connected.
• Disconnect headphones.
I - Batteries are exhausted.
• Insert fresh batteries.
- Batteries are incorrectly inserted.
• Insert the batteries correctly.
- Power cord is not securely connected.
• Connect the power ocrd properly.
Bad sound___________________
- Unsuitable speakers are used.
• Use supplied speakers.
- Batteries are exhausted.
• Replace batteries.
Poor bass sound
- Speakers not in phase.
• Connect speakers poles correctly,'+' to V ; t o
No sound on left or right side
- Speaker wrongly connected
• Connect speaker properly.
Beversed left and riflht sound____________
- Speakers are wrongly connected.
• Connect speakers properly, L to left, R to right.
- Set too close to TV. VCR or computer.
• Increase the distance.
Poor radio reception____________
- Weak radio signal.
• FM; aim and extend the telescopic aerial for best
reception;
• AM: rotate the entire set.
Poor caisatta sound quality________________
- Oust and dirt on the heads, capstan or pressure
roller.
• Clean the heads etc., see Maintenance.
~ Use of incompatible cassette types (METAL or
CHROME).
• Only use NORMAL (lEC 1) for recording.
Becording does not work_________________
- Cassette tab(s} may be broken out.
• Apply a piece of adhesive tape over the missing
tab space.
CP playback does not work * •
- CD is badly scratched or dirty.
• Replace or dean the CD, see Maintenance,
- No CD inserted.
• Insert CD.
- CD inserted upside down.
• Insert CO with printed side facing up.
The CD skips Iracipt
- Laser lens is steamed up.
• Wait until tens has acclimatized.
- CD is damaged or dirty.
• Replace or clean the CD.
- PR06RAM/SHUFFLE is active.
• Switch off the PROGRAM/SHUFFLE function.
Bemotc cowtrot does not function properly
- Batteries are exhausted.
• Insert new batteries.
- Batteries are incorrectly inserted.
• Insert batteries correctly.
- Distance between the set is too large.
• Reduce the distance.
14
15