Philips AZ2710-17 - Manual (Page 3)

CONHiOLS
0 IR SENSOR • Infrared remate sensor for remote
control reception.
(D DBB Dynamic Bass Boost To increase the bass
level.
C?) VOLUME A ▼ - To adjust the volume level.
C4; TONE CONTROL - To adjust the emphasis on high
or low tones.
( 5) ii - 3.5 mm headphone socket.
SOURCE SELECTOR - To select the source of
sound: CD-TUNER-TAPE/OF and to switch the
POWER ON/OFF.
(DDISnAY
CASSETTE RECORDBl
C^OECKI
RECORD •-To start recording,
PLAY ► - To start playback.
4M - To fast rewind the tape.
- To fast forward the tape.
8TOP*OPEN ■ 4 - To stop playback and open
the cassette compartment.
PAUSE II - To interrupt recording or playback.
®DECK2
PLAY ► - To start playback.
^ - To fast rewind the tape.
- To.fast forward the tape.
STOP^PEN ■ A • To stop playback and open
the cassette compartment.
PAUSE II ' To interrupt recording or playback.
CD PLAYER
@ MODE - e.g. to SHUFFLE or RD’EAT playback.
® PROGRAM - To program track numbers and to
review the program.
@ STOP ■ - To stop playback or erase a program.
@ OPEN - To open the CD door.
@ PLAY*PAUSE Mil - To start or interrupt CO play­
back.
@ SEARCH »w • To skip or search forwards to a pas­
sage or a track.
@ SEAUCH HM - To skip or search backwards to a
passage or a track.
RADIO
@BAND - To select the wave band ¡FM/AM).
TUNING - To tune to radio stations.
mymsmm
@ SPEAKER LEVERS - To unlock
boxes. ’ '
@ TELESCOPIC AERIAL - To imptwe lW recep­
tion. ' ^ ^ ■ •
SPEAKERS - Speaker terminals.
@ AC MAINS • Outlet for power cord.
^ BATTERY DOOR - To open the battery compart­
ment.
0 VOLUME A ▼ - To adjust the volume level.
(?) SHUFFLE - To select playback of tracks in random
order.
@ REPEAT - To repeat a track, a CD programme or
an entire CD.
® ► II - To start or interrupt CD playback
(D ■ - to stop playback or erase a CO programme
@ M or N - To skip to the beginning of a
current/previous or subsequent track
C?) SEARCH MM Of MH - To skip or search backwards
and forwards within a track
77» TUNER CONTWl fte/wiwfe
ow/ro/ hm m function with thb set.
Whenever convenient, use the power supply if you want to conserve
battery life. Make sure you remove the power plug from the set and wall
outlet before ih^ftîrtg batteries.
Batteries {optional)
f. Open the battery compartment and insert as shown six batteries,
type R20, UM1 or 0-cells.
RsnioM control batteries (included)
#. Open the battery compartment and insert as shown two batteries,
type AAA. R03 or UM4.
Z Replace the compartment door, making sure die batteries are firmly
andcorrectly in place.
J, Remove the batteries if exhausted or if they will not be used again for
a long period.
- The incorrect use of batteries can cause electrolyte leakage and will
corrode the compartment or cause the batteries to burst. Therefore:
- Do not mix battery types, e.g. alkaline with zinc carbonate.
-*• When inserting new batteries, replace all at batteries the same time.
Nit«».'The battery supply is switched off when the set is connected to
the mains.
Bsffsfiss coÊrtaia dtemha! substances, sa they sbouM ifc
cfpiopBrIy
1. Check if the power voltage as shown on the type plate (on the base of
the set! corresponds to your local power voltage. If it does not, consult
your dealer or service organisation.
2. Connect the power cord to the MAINS ~ outlet and the wall outlet.
- The set is now ready to use.
^ To switchaff the power completely, pull the power plug out of
r the wall outlet. u ' \ :
- Disconnect the pqyverl^ when you change over to battery supply, or
to protect the set duririg heavy dtunderstorms.
- To avoid overheating oi the^et a safety circuit has been built in.
Therefore your set may disconnect under extreme conditions, if this
■ happens, switch the set of and let it cool down before reusing it.
We have done our utmost to make the packaging easily
separable into tftfee nwio materials: cardboa«! (box), er^ndabte polystyrene (buffer) and polyedïylene (bags,
protective foam sheet).
Your set cMwisiti of nnterial» wkioli c«ii be recycled if diMwaseaibted by a i^eciatiatd com-
!»«»■
^aiisted batleriei eifdcldt^ttipwnt