How to set up and use your tv, Menu, Remote – Philips PR1308B User Manual
Page 4: Cüsm, Chtanned a/'w buttons, Menu button, Status/exit button, Television, Your
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
How
TO S
et
U
p
and
U
se
your
TV
O
M
enu
I—CBEGIND
o
( !
i i a n m
:
i
, A i
k
) M
i
; ,
m o
C
hannel Auto Memo (or
First Time Setup) takes
care of some basic TV settings
for you. Follow the steps in this
section:
• to set the language of the
TV’s menu
• to add channels into the
TV’s memory
•
to set the TV for Antenna or
Cable TV signal connect-
tions.
These instructions apply only
when you turn on the TV for the
first time. After the TV has been
turned on for the first time, or if
you want to set up the TV chan
nels and language later, refer to
the information on page 5.
Press the POWER
button to turn the TV ON.
Be sure to connect the TV
power cord to a standard AC
outlet.
The language selection menu
appears on the TV screen.
SELECT LANGUAGE
> ENGLISH
ON
ESPAÑOL
SELECT AT OR
PRESS MENU TO CONTINUE
Press the CH(annel) A/T
buttons to select English or
Spanish. Then, press the
MENU button.
Press the VOL(ume) + but
ton to begin automatic channel
setup.
When setup is complete,
CHANNELS ARE SET will
appear on screen.
-----------------------------------
Press the fl
STATUS/EXIT but
ton to exit the
SETUP menu.
R
emote
T
'o load the batteries into
the remote:
1. Slide off the battery com
partment lid on the
remote control.
2. Insert two AA batteries
(supplied) into the bat
tery compartment
as indi
cated by the + / - markings
inside the battery compart
ment. Batteries installed
incorrectly may damage
the remote control.
3. Replace the lid.
Battery
Compartment
Lid
—CüsM
r
Point the remote con
trol toward the remote sen
sor on the TV when operat
ing the TV with the remote.
POWER Button
Press to turn the TV ON and OFF.
Number Buttons
Press two number buttons to select TV
channels. For example, to select channel
6, press 0,6.
When you select cable channels which
are equal or greater than the number 100,
press the +100 button, then press the last
two digits of the channel you want. For
example, to select channel 117, press the
+100 button, 1,7.
CHtanneD A/'W Buttons
Press to scan through programmed ehan
nel numbers.
Press to select an item in the on-screen
menu.
MENU Button
Press to access the on-screen menu
SLEEP Button
Press to set the TV to turn itself OFF
automatically.
ALT. CH tAlternate ChanneD Button
Press to return to the TV channel you
were viewing immediately before switch
ing to your current channel.
VOLtumei +/- Buttons
Press to adjust the TV sound level. Press
to adjust the setting of an item in the on
screen menu (BRIGHTNESS, for exam
ple).
MUTE Button
Press to cancel the sound at the TV.
again to restore the sound.
Press
STATUS/EXIT Button
Press to display the channel number on
the screen or to remove the channel num
ber from the screen. Press to remove the
on-screen menu.
T
elevision
I—
IBEGIN>
l<$>
Press the POWER
button to turn the TV ON
or OFF.
Press the VOLUME
+/- buttons to adjust the
sound level.
Press the CHANNEL
A/T
buttons to select TV
channels.
Press the MENU button to dis-
The tuned g
play the TV’s menu.
channel number ~
Press the CHANNEL
A/T
buttons
will appear briefly
to select an item in the menu.
when you turn on
Press the VOLUME +/- buttons to
the TV and when
adjust an item in the menu
you change chan-
(BRIGHTNESS, for example).
nels. The channel
Note: Use the CHANNEL A/T but-
number will remain
tons to select EXIT, then press the
on the screen at all
VOLUME + button to remove the
times if you set
menu.
REMINDER to ON.
S
Details are on page
f
6.
Note
You can connect earphones (not supplied) to the EARPHONE jack on the front of the eabinet if you want to
enjoy private personal listening.
-4-