G-Shock GA110SN - Manual (Page 10)

Operation Guide 5145
99
AUTO ●
This setting enables the auto summer time setting, which turns summer time on
or off in accordance with the received time calibration signal.
OFF ●
This setting turns off summer time, and displays the current time normally.
ON ●
This setting turns on summer time.
Selecting this setting displays the DST indicator, and advances the current x
time setting by one hour.
Note that the above setting toggles between x “OFF” and “ON” when any city code
that does not support calibration signal reception (page 39) is selected.
98
See x “World Time City Code List” (page 73) for a complete list of city codes.
Holding down either button changes the setting at high speed. x
3.
Press D to change to the summer time setting.
Confi gure the summer time setting you want. x
4.
Use D to cycle through the summer time settings
until the one you want is displayed.
Pressing x D to cycle through the summer time (DST)
settings described below.
97
Confi guring Time and Date Settings ■
1.
In the Timekeeping Mode, hold down A for about
two seconds until the watch beeps and “ADJ”
appears on the display.
The currently selected city code will be fl ashing on the x
screen.
The watch will exit the setting screen automatically
x
if you do not perform any operation for about two or
three minutes.
2.
Use D (Eastward) and B (Westward) to scroll
through the city codes until the one you want to
use as your Home City is displayed.
Display the time zone that you want to select as your x
Home Time Zone.
VHFRQGLQWHUYDO
&LW\FRGH
Ŏ
7<2 7RN\R
96
Time and Date Settings
You can use the following procedure to set the current time and date of the Home
City that you have selected in the Timekeeping Mode.
Always use the Timekeeping Mode to set and adjust the current time and date x
settings.
You also can turn Power Saving on or off while setting the time and date. x
The watch automatically adjusts its analog setting to match the current digital
setup of your Home City.
If the analog time is not correct even though you are sure the digital setup of
your Home City is correct and the watch is performing signal reception properly,
check the home positions of the hands and make adjustments if necessary
(page 106).
95
+RXUO\7LPH6LJQDO2II
A
+RXUO\7LPH6LJQDO2Q
94
Stopping the Alarm Tone ■
Pressing any button while the alarm tone is sounding will stop it.
Turning the Hourly Time Signal On or Off ■
1.
In the Alarm Mode, use D to display the hourly time signal screen.
2.
Press A to toggle the hourly time signal between ON and OFF.
“ x ” appears on the display when the hourly time signal is off. “ ” appears
on the display when the hourly time signal is on.
93
$ODUP2II
A
$ODUP2Q
2-second
interval 2-second
interval
$ODUPWLPH $ODUPWLPH
92
Turning the Alarm On or Off ■
1.
In the Alarm Mode, use D to display the alarm screen.
2.
Press A to toggle the alarm between ON and OFF.
“ x ” appears on the display when the alarm is off.
“ ” appears on the display when the alarm is on.
On the alarm screen, the display alternates between the alarm ON/OFF setting x
and the alarm time setting.
91
5.
Use D (+) and B (–) to change the minute setting.
Holding down either button changes the setting at high x
speed.
6.
When the setting is the way you want, press A to exit the setting screen.
The watch also will exit the setting mode if you do not perform any operation for x
about two or three minutes.
Ŏ
90
3.
Use D (+) and B (–) to change the hour setting.
Holding down either button changes the setting at high x
speed.
When setting the hour, make sure you specify AM
x
(no indicator) or PM (P) correctly when using 12-hour
timekeeping, or that you specify the correct 24-hour time.
The same 12-hour/24-hour format you select for the
x
Timekeeping Mode time is also applied in the Alarm Mode.
4.
Press C to move the fl ashing to the minute
setting.
Ŏ
0LQXWHV