Casio 5132 - Manual (Page 2)

2
Operation Guide 5132
Mode Reference Guide
Your watch has four “modes”. The mode you should select depends on what you
want to do.
To do this: Enter this mode:
View the current time in your Home City and in one of •
29 cities around the globe
Configure Home City and daylight saving time (DST)
•
settings
Configure time and date settings
•
Timekeeping Mode
Use the stopwatch to measure elapsed time Stopwatch Mode
View the current time in one of 29 cities (time zones) around
the globe
World Time Mode
Set an alarm time Alarm Mode
Selecting a Mode
With this watch, everything starts from the Timekeeping Mode.
To determine the watch’s current mode
Check the position of the v Left Dial Hand as shown
under “To select a mode”.
To return to the Timekeeping Mode from any other
mode
Hold down C for about two seconds until the watch beeps
twice.
To select a mode
Press C to cycle between the modes as shown below. The v Left Dial Hand
indicates the currently selected mode.
>
Timekeeping Mode Stopwatch Mode
Alarm Mode World Time Mode
The hand indicates
the day of the week.
The hand points to 0.
The hand points to ALM. The hand points to STD
or DST.
C
Timekeeping
Use the Timekeeping Mode to view the current time and date. To enter the
Timekeeping Mode from any other mode, hold down C for about two seconds.
Hand Functions
z
Hour Hand
x Second Hand
c Minute Hand
v Left Dial Hand: Indicates the day of the week.
b Lower Dial Hand: Indicates the current hour in the
Home City time in 24-hour format.
n Right Dial Hands:
Indicate the current time in the World Time City in
24-hour format.
m Day
Configuring Home City Settings
There are two Home City settings: actually selecting the Home City and selecting
either standard time or daylight saving time (DST).
To configure Home City settings
Note
This watch does not have a city code that corresponds •
to Newfoundland.
In the Timekeeping Mode, keep 1. A depressed (for about
five seconds) as the x Second Hand moves to the city
code of the currently selected Home City.
This indicates the city code setting mode. •
The watch will exit the setting mode automatically if •
you do not perform any operation for about two or
three minutes.
For details about city codes, see the “City Code •
Table”.
To change the Home City setting, press 2. D to move the
x Second Hand clockwise.
Keep pressing • D until the x Second Hand is pointing
at the city code you want to select as your Home City.
Each time you select a city code, the • z Hour Hand,
c Minute Hand, b Lower Dial Hand and m Day
move to the current time and date for that city code.
Do not perform the next operation until these hands
stop moving.
Press 3. B to toggle the time for the currently selected
city code between STD (standard time)/DST (daylight
saving time).
In the city code setting mode, the • v Left Dial Hand indicates the current daylight
saving time setting as STD (standard time) or DST (daylight saving time).
Note that you cannot switch between • STD (standard time)/DST (daylight saving
time) while UTC is selected as your Home City.
After the setting is the way you want, press 4. A to return to the Timekeeping Mode.
>
B +
* 6 > 5
@
@
B +
* > 5 @
To toggle the Home City time between standard time and daylight saving time
Perform the step 1 under “To configure Home City settings”. 1.
Each time you select a city code, the • z Hour Hand, c Minute Hand, and
b Lower Dial Hand move to the current time for that city code. Do not perform
the next operation until these hands stop moving.
Press 2. B to toggle the time for the city code of the currently selected Home City
between STD (standard time)/DST (daylight saving time).
In the city code setting mode, the • v Left Dial Hand indicates the current daylight
saving time setting as STD (standard time) or DST (daylight saving time).
Note that you cannot switch between • STD (standard time)/DST (daylight saving
time) while UTC is selected as your Home City.
After the setting is the way you want, press 3. A to return to the Timekeeping Mode.
Note
After you specify a city code, the watch will use UTC* offsets in the World Time •
Mode to calculate the current time for other time zones based on the current time
in your Home City.
Coordinated Universal Time, the world-wide scientific standard of timekeeping. The *
reference point for UTC is Greenwich, England.
Configuring Current Time and Date Settings
You can configure current time and date settings.
To change the current time setting
In the Timekeeping Mode, keep 1. A depressed (for about
five seconds) as the x Second Hand moves to the city
code of the currently selected Home City.
At this time, the • v Left Dial Hand will indicate the
Home City’s current daylight saving time setting (STD
or DST).
Change the Home City and daylight saving time (DST) 2.
settings, if you want.
For details about these settings, see steps 2 and 3 •
under “To configure Home City settings”.
In the following steps, each press of
• C cycles
between settings as shown below.
Home city/DST Hour/Minute Year
Day Month
Press 3. C .
The watch will beep, and the • x Second Hand and v Left Dial Hand will move to
their 12 o’clock positions. This is the time setting mode.
Use 4. D (+) and B (–) to change the time (hour and minute) setting.
Each press of either button will move the hands ( • z Hour Hand and c Minute
Hand) one minute.
Holding down • D or B will start high-speed z Hour Hand and c Minute Hand
movement in the applicable direction. To stop high-speed hand movement,
press any button.
The
• b Lower Dial Hand and z Hour Hand move in sync with each other.
When setting the time, make sure that the • b Lower Dial Hand indicates the
proper a.m./p.m. hour.
If you want to change the date setting at this time, press
• C and perform the
procedure starting from step 3 under “To change the current date setting”.
After the time setting is the way you want, press 5. A to return to the Timekeeping
Mode.
This will cause the • x Second Hand to move automatically to 12 o’clock and
resume movement from there.
To change the current date setting
@
00
60
10
40
20
30
70
90
80
50
Setting the year (tens digit)
In the Timekeeping Mode, keep 1. A depressed
(for about five seconds) as the x Second Hand
moves to the city code of the currently selected
Home City.
Press
2. C twice.
The watch will beep and change to the year •
setting mode.
The year can be set in the range of 2000 to
•
2099.
You can save your settings and exit the
•
setting procedure at any time by pressing A,
which will return to the Timekeeping Mode.
This will cause the x Second Hand to move
automatically to 12 o’clock and resume normal
movement from there.
Use 3. D to change the tens digit of the year setting.
Each press of • D will move the x Second Hand and change the tens digit of the
year setting.
After the tens digit of the year setting is the way you want, press 4. C .
The watch will beep and change to the ones digit of the year setting mode. •
@
0
6
1
4
2
3
7
9
8
5
Setting the year (ones digit)
Use 5. D to change the ones digit of the year
setting.
Each press of • D will move the x Second
Hand and change the ones digit of the year
setting.
After the ones digit of the year setting is the way 6.
you want, press C.
The watch will beep and change to the month •
setting mode.
> @
B +
*
@
>