I.C.E. GIDM-325 User Manual
Page 16
15
ECONOMITE 400-33 & F400-33 GAS BURNERS
WARNING: Explosion hazard. Can cause serious injury or death. This device can malfunction if it gets wet. Never try to use a device
that has been wet - replace it.
DECODING CENTURY MOTOR NUMBERS. Single digit prefix denotes manufacturer’s location. Double digit suffix denotes
manufacturer’s mechanical code.
PART #
DESCRPTION
PART #
DESCRIPTION
3981-001 4” Diameter Stainless Sleeve
5253-01
Pilot assembly with insulators, rods, temflex and
baffle.
4904-45
Quadrant-Air Shutter Adjustment
5253-10
PVC tubing—7/16”I.D. x 2” long
4905-15
Air shutter-Internal
5234-40
Flame rod Gland Nut
4917-00
Main Orifice Holder
5234-50
Flame rod assembly.
4918-11
Orifice Elbow (1” NPT)
5249-01
Pilot air baffle.
4919-60
Blower Wheel with centrifugal actuator and Disc
5249-32
Spark rod assembly.
4919-90
Centrifugal Actuator Disc
5250-00
Pilot tip with cone less insulators, rods, temflex
and baffle.
4927-509 1/6 HP motor 120/1/60 [G.E. 5KH35FN123X
5272-00
Blower inlet grille.
(note 1/3 HP substitute), 5KH33DG655Y,
5KH33DN171Y; Dayton 6K149; Marathon
5939-01
Flame rod wire--5” through 9” burner tube.
48S34D191A, 48S34D203; Universal Electric
HH1E001N; Century X-173668-XX]
8433-06
Pilot spud (.021)—PROPANE (3N4-021,
Y90AA-5232).
4922-90
Primary Air Shutter Kit
8433-10
Pilot spud (.032)—NATURAL (2-15M1-032,
4924-10
Inlet Side Plate
Y90AA-5232).
4944-02
Main Spud 25/64” (.390) minimum capacity--
8437-419 1/6HP totally enclosed motor 115/1/60 (Century
NATURAL—drill 7/16” (.437) for 400/540 MBH
X-176797-XX) special and Canadian burners
range and omit for 540/700 range
only. Not interchangeable with drip proof motor
4921-50.
4944-03
Main Spud #21 Drill(.390) minimum capacity--
PROPANE—drill for desired capacity per manual
8447-11
Ignition transformer 120/1/60 primary, 6000 volts
secondary (Webster 612-6A020, 612-6A044;
4944-10
Main Spud Extension
France 3RABVR-19; Jefferson #638-181).
4946-00
Motor Spacer (4 required)
8450-21
Orifice holder sealing gasket.
4959-05
External Pilot Air Tube Kit
8451-06
Spark rod insulator sleeve.
5201-00
½” sq. pass thru for 1/4” tube fitting (gas line)
8484-72
Heyco strain relief (SR-4K-1)--Flame rod wire.
5201-10
½” sq. pass thru for 5/16” tube fitting (air line)
8484-75
Heyco strain relief (SR-11-2)--Spark rod wire.
5202-08
Pilot Spud #55 (.052) drill [was #54(.055)]--
8484-78
Heyco snap bushing (B-8875-750).
NATURAL AND PROPANE
8502-05
Spark cable--15” burner tube.
5211-51
Motor, wheel and side plate assembly 120/1/60
8502-06
Spark cable--5” through 9” burner tube.
5225-263 Blower housing and burner tube assembly--9”
8423-16
Blower interlock switch (MICRO BZ-2RQ174-A2).