Great Planes SU-31 3D ARF - GPMA1412 User Manual
Page 6
6
ADDITIONAL ITEMS REQUIRED
Adhesives & Building Supplies
This is the list of Adhesives and Building Supplies that are
required to fi nish the Sukhoi SU-31 1.60 ARF.
❏
Pro
™
30-minute epoxy (GPMR6047)
❏
1/2 oz. [15g] Thin Pro CA+ (GPMR6001)
❏
1/2 oz. [15g] Medium Pro CA+ (GPMR6007)
❏
Hobbico 60 watt soldering iron (HCAR0776)
or
❏
Hobby Heat
™
Micro Torch II (HCAR0755)
❏
Silver solder w/fl ux (STAR2000)
❏
Petroleum jelly (Vaseline
®
)
❏
3' [900mm] Standard silicone fuel tubing (GPMQ4131)
(for glow engine only)
❏
R/C foam rubber (1/4" [6mm] – HCAQ1000)
❏
Drill bits: 1/16" [1.6mm], 3/32" [2.4mm], 7/64" [2.8mm],
9/64" [3.6mm] 7/32" [5.6mm], 3/16" [4.8mm]
❏
Denatured alcohol (for epoxy clean up)
❏
8-32 Tap and drill set (GPMR8103) (for glow engine only)
❏
Tap handle (GPMR8120) (for glow engine only)
❏
#1 Hobby knife (HCAR0105)
❏
#11 Blades (5-pack, HCAR0211)
❏
Masking tape (TOPR8018)
❏
T-pins (HCAR5150)
❏
Great Planes Pro Threadlocker (GPMR6060)
❏
Dead Center
™
Engine Mount Hole Locator (GPMR8130)
❏
Panel Line Pen (TOPQ2510)
❏
1" [25mm] Double-sided foam mounting tape (GPMQ4442)
❏
220-grit Sandpaper (GPMR6185)
❏
21st Century
®
sealing iron (COVR2700)
❏
21st Century iron cover (COVR2702)
Optional Supplies & Tools
Here is a list of optional tools mentioned in the manual and other
items that will help you build the Sukhoi SU-31 1.60 ARF.
❏
Fuel fi ller valve for glow fuel (GPMQ4160)
❏
Fuel fi ller valve for gasoline (GPMQ4161)
❏
1/2 oz. [15g] Thick Pro CA- (GPMR6013)
❏
Stick-on segmented lead weights (GPMQ4485)
❏
Epoxy brushes (6, GPMR8060)
❏
Mixing sticks (50, GPMR8055)
❏
Mixing cups (GPMR8056)
❏
Builder’s Triangle Set (HCAR0480)
❏
36" Metal ruler (HCAR0475)
❏
Pliers with wire cutter (HCAR0630)
❏
Hobbico Duster
™
can of compressed air (HCAR5500)
❏
Rotary tool such as Dremel
®
❏
Rotary tool reinforced cut-off wheel (GPMR8200)
❏
Servo horn drill (HCAR0698)
❏
CG Machine
™
(GPMR2400)
❏
#64 Rubber bands (1/4 lb [113g] box, HCAQ2020)
IMPORTANT BUILDING NOTES
• There are two types of screws used in this kit:
• Self-tapping screws are designated by a number and
a length. For example #6 x 3/4" [19mm]
This is a number six screw that is 3/4" [19mm] long.
•
Machine screws are designated by a number, threads
per inch, and a length. For example 4-40 x 3/4" [19mm]
This is a number four screw that is 3/4" [19mm] long
with forty threads per inch.
•
When you see the term test fi t in the instructions,
it means that you should fi rst position the part on the
assembly without using any glue, then slightly modify
or custom fi t the part as necessary for the best fi t.
•
Whenever the term glue is written you should rely upon
your experience to decide what type of glue to use. When
a specifi c type of adhesive works best for that step, the
instructions will make a recommendation.
•
Whenever just epoxy is specifi ed you may use either
30-minute (or 45-minute) epoxy or 6-minute epoxy. When
30-minute epoxy is specifi ed it is highly recommended
that you use only 30-minute (or 45-minute) epoxy,
because you will need the working time and/or the
additional strength.
•
Photos and sketches are placed before the step they
refer to. Frequently you can study photos in following
steps to get another view of the same parts.
•
The Sukhoi SU-31 1.60 ARF is factory-covered with high
quality heat-shrink fi lm. Should repairs ever be required,
this fi lm can be patched with Top Flite
®
MonoKote
®
purchased separately. MonoKote is packaged in six-foot
rolls, but some hobby shops also sell it by the foot. If
only a small piece of MonoKote is needed for a minor
patch, perhaps a fellow modeler would give you some.
MonoKote is applied with a model airplane covering iron,
but in an emergency a regular iron could be used. A roll
of MonoKote includes full instructions for application.
Following are the colors used on this model and order
numbers for six foot rolls.
True Red – TOPQ0227
Metallic Blue – TOPQ0402
Cub
Yellow
–
TOPQ0220
White
–
TOPQ0204
Metallic Charcoal – TOPQ0407