Great Planes Dazzler 40 ARF - GPMA1038 - Manual (Page 4)

4
5
1
1
2
3
4
6
7
8
9
10
11
15
16
12
14
13
1 Wing
2 Fuselage
3 Stab
4 Fin
5 Fuel Tank Assembly
6 Spinner
7 Wing Tape
8 Pushrods
9 Aileron Pushrods
10 Main Wheels (2)
11 Tailwheel Assembly
12 Servo Tray
13 Wing Joiner
14 Servo Tray Mounting Rails
15 Radio Compartment Cover
16 Foam Rubber
(2) .074 x 36" pushrod wire, threaded one end
(elevator, rudder)
(2) .074 x 6" pushrod wire, threaded one end (aileron)
(4) Large control horn (elevator/rudder/aileron)
(8) 2-56 x 1/2" machine screws (elev/rudder/ail)
(4) Nylon clevises (elevator/rudder/(2)aileron)
(4) Nylon Faslink (elevator/rudder/(2)aileron)
(4) 5/32" wheel collar (for main landing gear)
(4) 6-32 set screw (for the wheel collars)
(4) Silicone clevis retainers (elevator/rudder/(2)aileron)
(17) 2 x 1/2" sheet metal screws (L.G. straps, battery
compartment, tail wheel bracket)
(2) Screw lock connector (throttle linkage)
(2) Nylon retainer (throttle linkage)
(2) 4-40 x 1/4" Socket head cap screw (throttle linkage)
(1) Wire cable .056 x 36" (throttle linkage)
(1) Plastic tube (throttle linkage)
(4) Nylon hump landing gear strap (landing gear)
(4) 3mm x 20mm bolts (Pre-installed for engine mount)
(4) 3mm washer (Pre-installed for engine mount)
(4) 3mm lock washer (Pre-installed for engine mount)
(4) 3mm blind nut (Pre-installed for engine mount)
(4) 1mm screws (Pre -installed in fuel tank hatch)
(2) Aluminum straps (mounting engine to engine mount)
(4) 8/32 bolts (for mounting engine to the engine
mounting straps and engine mount)
(8) 8-32 nuts (for mounting engine to the engine
mounting straps and engine mount)
(4) 8-32 lock washers (for mounting engine to the
engine mounting straps and engine mount)
(2) 1mm machine screws (tailwheel bracket)
(1) 1mm wheel collar (retains tailwheel)
(1) 2mm allen set screw (for wheel collar)
(4) 1/4" x 9/16" x 9/16" wood block
(6) wooden triangle gussets
(4) Nylon straps (mounting belly pan)
(1) Main landing gear
(2) Outer pushrod tubes (installed)
(1) Decal sheet
Kit Contents (Not Photographed)
Kit Contents
(Photographed)
KIT CONTENTS
0" 1" 2" 3" 4" 5" 6" 7"
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180
Inch Scale
Metric Scale
To convert inches to millimeters, multiply inches by 25.4
Before starting to build, use the Kit Contents list to take an inventory of this kit to make sure it is complete and inspect
the parts to make sure they are of acceptable quality. If any parts are missing or are not of acceptable quality, or if you
need assistance with assembly, contact Great Planes Product Support. When reporting defective or missing parts, use
the part names exactly as they are written in the Kit Contents list on this page.
3002 N. Apollo Drive, Suite 1
Champaign, IL 61822
Telephone: (217) 398-8970
Fax: (217) 398-7721
E-mail: [email protected]