Great Planes U-Can-Do SF EP/GP .80 ARF - GPMA1272 - Manual (Page 4)

4
manufacturer’s recommendation. The order number for the
recommended engine is provided below. If you plan to install
the recommended O.S. engine, we found that the APC 13 x 6
propeller works well.
❍ O.S. 65AX ABL w/Muffl er (OSMG0558)
❍ APC 13x6 Sport Propeller (APCQ1306)
Brushless Motor Recommendations
If you are planning on using electric power, we recommend
the RimFire .80 brushless motor and a 60A ESC. A 15x6
electric propeller is a good choice with the recommended
motor. Many batteries will work as a fl ight battery. We suggest
the 22.2V 3350mAh EON-X Flight Power pack. Part numbers
are provided below:
❍ Great Planes RimFire .80 50-55-500 Outrunner
Brushless (GPMG4740)
❍ Great Planes Silver Series 60A Brushless ESC High
Volt (GPMM1850)
❍ APC 15x6 Thin Electric Propeller (APCQ1505)
❍ FlightPower LiPo EON-X 30 6S 22.2V 3350mAh 30C
(FPWP6358)
It is recommended to make a battery lead extension if
installing a brushless motor. Part numbers needed to make
the extension are as follows:
❍ W.S. Deans ® Female Ultra Plug ® w/Pigtail
(WSDM3010)
❍ W.S. Deans
® Male Ultra Plug ® (2) (WSDM1302)
If you need a charger for your fl ight battery, we suggest either
the Triton EQ or Triton 2 EQ. Both are very versatile chargers
that can charge virtually any hobby battery currently available.
❍ Great Planes ElectriFly Triton EQ AC/DC Charger
(GPMM3155)
❍ Great Planes ElectriFly Triton2 EQ AC/DC Charger
(GPMM3156)
ADDITIONAL ITEMS REQUIRED
Required Hardware & Accessories
This is the list of hardware and accessories required to fi nish
the U-Can-Do SF. Order numbers are provided in parentheses:
❍ R/C foam rubber 1/4" [6mm] (HCAQ1000)
❍ 3' [900mm] standard silicone fuel tubing (GPMQ4131)
(glow engine only)
Adhesives and Building Supplies
This is the list of Adhesives and Building Supplies that are
required to fi nish the U-Can-Do SF ARF:
❍ 1/2 oz. [15g] Thin Pro CA (GPMR6001)
❍ Pro 6-minute or 30-minute epoxy (GPMR6045 or
GPMR6047)
❍ Threadlocker thread locking cement (GPMR6060)
❍ Denatured alcohol (for epoxy clean up)
❍ Drill bits: 1/16" [1.6 mm], 5/64" [2 mm], 3/32" [2.4mm],
1/8" [3.2 mm], 11/64" [4.4 mm ]
❍ Rotary tool with cutting bit
❍ Great Planes Heat Shrink Tubing 3/8x3" (3)
(GPMM1060)
❍ Revell Premium Soft Handle Knife w/Blades (5)
(RMXR6900)
❍ Top Flite MonoKote sealing iron (TOPR2100)
❍ Top Flite Hot Sock iron cover (TOPR2175)
❍ Panel Line Pen (TOPQ2510)
❍ Hobbico Steel T-Pins 1" (100) (HCAR5100)
❍ Small clamps
❍ Masking tape
❍ Household oil
Optional Supplies and Tools
Here is a list of optional tools that will help you build the
U-Can-Do SF ARF:
❍ 1/2 oz. [15g] Thick Pro CA- (GPMR6013)
❍ 1/2 oz. [15g] Medium Pro CA+ (GPMR6007)
❍ 2 oz. [57g] spray CA activator (GPMR6035)
❍ 4 oz. [113g] aerosol CA activator (GPMR6034)
❍ CA applicator tips (HCAR3780)
❍ CA debonder (GPMR6039)
❍ Epoxy brushes 6, (GPMR8060)
❍ Mixing sticks (GPMR8055)
❍ Mixing cups (GPMR8056)
❍ Pliers with wire cutter (HCAR0630)
❍ T.A. Emerald Performance Duster Compressed Air
(TAEC1060)
❍ Servo horn drill (HCAR0698)
❍ Hobby Heat micro torch II (HCAR0755)
❍ Dead Center
™ Engine Mount Hole Locator
(GPMR8130)
❍ DuraTrax Ultimate Body Reamer (DTXR1157)
❍ Precision Magnetic Prop Balancer (TOPQ5700)
❍ AccuThrow Defl ection Gauge (GPMR2405)
❍ CG Machine (GPMR2400)
❍ Hobbico Flexible 18" Ruler Stainless Steel
(HCAR0460)
❍ Top Flite MonoKote trim seal iron (TOPR2200)
❍ Top Flite MonoKote heat gun (TOPR2000)
❍ Hobbico Pin Vise 1/16 Collet w/6 Bits (HCAR0696)
❍ Hobbico 8-Piece Ball Tip Hex L Wrench SAE
(HCAR0520)
❍ Hobbico 7-Piece Ball Tip Hex L Wrench Metric
(HCAR0521)
❍ Great Planes Clevis Installation Tool (GPMR8030)
❍ Great Planes Precision Prop Reamer Standard
(GPMQ5006)
❍ Great Planes Precision Prop Reamer Metric
(GPMQ5007)