Philips CD 634 - Manual (Page 9)

FAVORITE TRACK SELECTIONS (FTS)
For each CD you can store two programs in the player’s permanent
(FTS) memory.
Your favorite track selections of a given CD can then be called up
and played whenever you wish.
The selections will remain stored in the FTS memory even if you play
the entire disc or compile a different program from it.
The number of CDs which can be stored in the FTS memory
depends on the number of tracks in each program.
STORING A FAVORITE TRACK SELECTION (FTS and STORE)
• Compile your program as described in the ’PROGRAMMING’
section (add in or take out).
• Press FTS 1.
- FTS MEMO 1 starts flashing.
• Press S(tore).
-
STORED lights up, followed by the ranking number of this
program.
- The selection is now stored in the FTS 1 memory under this
number.
If you wish to store a further selection from the same CD:
•
Press STOP/CM (if you have stored the first program during
playback you must press STOP/CM twice).
• Compile the second program.
• Press FTS 2.
- FTS MEMO 2 starts flashing.
• Press STORE.
- STORED lights up, followed by the ranking number of this
program.
- The selection is now stored in the FTS 2 memory under this
number.
NOTE!
- If a selection of a particular CD has already been stored, then it
is automatically erased and the new selection is stored under the
old ranking number.
- If NO SPACE appears, then the FTS memory is full; you must
erase one or more old FTS programs to make room to store the
new program.
- If NO PROGRAM appears, then no program has been compiled
first.
FTS PROGRAMMED PLAY (FTS and PLAY/REPLAY)_____________________
• Press FTS 1 or FTS 2.
- FTS MEMO 1 or FTS MEMO 2 starts flashing.
• Press PLAY/REPLAY.
- PROGRAM PMYlights up and the chosen selection will now be
played.
• Press STOP/CM twice if you wish to revert to normal play.
If NOT IN FTS 1, NOT IN FTS 2 or NO FTS FOUND appears, no
favorite selection has been stored.
All buttons (except EDIT, PRESETS, TfTLE and INFO) can be used
while a favorite selection is being played.
Search for a passage is only possible in the track which is being
played.
As long as the player is in the direct programming mode (DIRECT
PROG) you can continue to add to the program during playback.
CHECKING THE FTS MEMORY (INFO)
• Press INFO (in STOP mode).
-
FTS INFO lights up; the following information appears on the
display in this order:
- The number of CDs in the FTS 1 and FTS 2 memory. For example:
FTS1 04 DISC and FTS2 05 DISC.
If the FTS memory is empty, then you will see FTS 1 EMPTYand/or
FTS 2 EMPTY.
- The number of spaces available in the memory.
For example; 112 SPACE.
- The number of times that the CDs in the FTS 1 and FTS 2 memory
have been played: FTS1 INFO, followed by, for example,
NR 01 03 PL. NR 02 05 PL. etc.
FTS2 INFO, followed by, for example, NR 01 04 PL,
NR 02 06 PL, etc.
- Then TITLEMEMORYappears. You are now given information on
the ’names’ which you have given to CDs and/or track numbers.
For this refer to: ’NAMING CDs AND TRACK NUMBERS’ under
’OTHER POSSIBILITIES’.
With NEXT you can proceed more rapidly to the next block of
information.
ERASING A FAVORITE TRACK SELECTION (CLEAR)__________________
• Press INFO (in STOP mode).
- FTS INFO lights up.
• Press NEXT until the ranking number appears on the display: for
example NR 02 01 PL.
• Hold C(lear) pressed down until DELETED lights up.
- The selection has now been erased.
If you do not know the ranking number:
• Load the CD and close the CD compartment.
• Press FTS 1 or FTS 2.
- FTS MEMO 1 or FTS MEMO 2 starts flashing.
• Hold C(lear) pressed down until DELETED lights up.
- The selection has now been erased.
ERASING THE ENTIRE FTS MEMORY (REPEAT and CLEAR) •
• Press FTS 1 or FTS 2.
- FTS MEMO 1 or FTS MEMO 2 starts flashing.
• Pres REPEAT and then press C(lear) immediately.
• Hold both buttons pressed down until
CLEARING ALL lights up.
followed by ALL CLEARED.
- The entire FTS memory has now been erased.