Futaba 2NBR - Manual (Page 2)

FEATURES OF NEW ATTACK NEW ATTACK-R AND NEW ATTACK-BFR
The NEW ATTACK, NEW ATTACK-R has a BEC function.
The NEW ATTACK-BFR has BEC & ASP functions.
•The BEC (Battery Eliminator Circuitry) system is a high performance constant voltage
circuit (regulator). Since the running Nicd battery can also be used as the receiver servo
power supply, there is no troublesome wiring and the vehicle can be made lighter.
(Installed in NEW ATTACK, NEW ATTACK-R and NEW ATTACK-BFR.)
•The ASP (Adjustable Safety Position) system prevents loss of steering control. It is a
safety system which protects the vehicle against loss of control due to a discharged Nicd
by detecting a drop in the voltage of the shared power supply Nicd battery and auto-
matically sets the throttle servo to the drive motor off position preset at the transmitter
then allows steering with the remaining power before steering control is lost. When the
voltage of the running Nicd battery recovers, ASP is automatically reset and the normal
running functions are recovered by turning on the transmitter power switch. (Installed
in NEW ATTACK-BPR)
World's first safety system that allows running of the vehicle up to the finish
line while using the capacity of the power supply to the fullest without a loss of
steering control even when the voltage of the running Nicd battery drops.
•Transmitter is Built-in servo reverse switches. (New ATTACK-R, NEW ATTACK-BFR)
TRANSMITTER FP-T2NBL/T2NBR/T2NBFR SERVO FP-S128
SMALL, RUGGED, HIGH NEUTRAL SERVO
•ASP (Adjustable Safety Position) system allows safe
recovery without a loss of steering control. (T2NBFR
only)
•New swivel stick system that allows selection of the
stick lever operating direction over a range of 10°.
•Racing specification short aluminum stick lever makes
operation extremely easy.
•New neutral lever allows setting of the neutral position
of the throttle stick in two stages. Perfectly matched to
the throttle position of motor and engine cars. The stick
can be changed to a ratchet system by installing an
optional slider.
• Servo reverse switches (steering & throttle).
Since each servo can be switched between forward and
reverse from the outside of the transmitter, linkage
hookup is extremely easy. (T2NBR, T2NBFR)
• Level meter shows the state of the battery at a glance.
•Crystal can be changed from the outside. (Except 72.I
75MHz)
• Hook. Optional neck strap can be used.
RECEIVER FP-R102GF
•BEC (Battery Eliminator Circuitry) system allows
sharing of the running Nicd battery and eliminates the
need for a regulator and diode.
•High performance 2 channel receiver with ASP system
when used with the proper transmitter.
•Crystal socket uses a new type of highly reliable sub-
miniature pins. Reliability is increased and the crystal
can be changed from the outside.
•Skew type armature motor.
Movement of the trimmer by even one notch is tracked
by a skew type motor which displays a performance
near that of a coreless motor.
• New indirect drive potentiometer improves vibration
and shock resistance and neutral accuracy.
• Futaba low-power custom 1C provides extremely high
torque, narrow dead band, and superior tracking.
• Fiberglass reinforced PBT (polybutylene terephthalate)
injection molded servo case is mechanically strong and
invulnerable to glow fuel.
•Strong polyacetal resin ultra-precision servo gear fea-
tures smooth operation, positive neutral, and very little
backlash.
• Fiberglass reinforced epoxy resin PC board with thru-
the-hole plating improves servo amp vibration and shock
resistance.
• Three pin connector eliminates faulty contact and im-
proves reliability against vibration and shock. Housing
has a reverse insertion prevention mechanism.
•Special grommet simplifies mounting of the servo and
has an excellent cushioning effect.
•Six special adjustable splined horns.
•High 48.7oz.jn (3.5kg-cm) maximum output torque
allows use in almost any model.
1