VTech 917ADX - Manual (Page 13)

O P E R A T I N G I N S T R U C T I O N S O P E R A T I N G I N S T R U C T I O N S
■ Press 1, 2 3, or 4 on the Handset to select
a ringer type. The Handset will emit the cor­
responding ringer tone.
■ Press OFF on the Handset to exit pro­
gramming.
rURNING OFF THE HANDSET RINGER
■ The Handset must
3e OFF
■ Press PRG/PRV on
he Handset
MEMORY DIALING
■ Press # or * key on
he Handset
■ Press 5 to turn off
he ringer
I Press OFF key to
ixit
MEMORY DIALING
BASE RINGER
CONTROL
I This control switch is located on the right
and edge of Base Unit.
I Select HIGH. LOW or OFF setting.
CHECKING THE HANDSET RINGER v
I To check the ringer type which is currently
rogrammed, do the following:
I Handset must be OFF
I Press PRG/PRV on the Handset
I Press # key on the Handset
I Press 0 on the Handset. The phone will
ring once to show ringer selected.
I Press OFF key to exit
HThe Si 7 ADX cordless phone can store up
to10 frequently dialed numbers in memory.
■ Memory Dial numbers must be stored us­
ing the Handset, but can be recalled from ei­
ther the Base Unit or the Handset.
TO STORE A NUMBER INTO MEMORY
■ The Handset must be OFF
I Press PRG/PRV on the Handset
BPress the Memory
Location key where the
phone number will be
stored (0-9)
■ Dial the number you
want to store. The num­
ber can be up to 16
digits long
■ Press MEM on the
Handset to complete
programming
■ if programming has
been successful,a
happy tone will be
generated.
■ If programming was unsuccessful, a sad
tone is generated.
■ If the phone is left unattended in program
mode for longer than 30 seconds, it will gen­
erate a sad tone and automatically exit pro­
gram mode.
■ Write down the phone number you as­
signed to each Memory Location key on the
iVFiSI
CO H3 E3
QBE)
OBE
Q B in)
directory card in the Base Unit cradle.
TO DIAL A NUMBER FROM MEMORY
^You can Memory Dial from either the
Handset or the Base Unit.
■ Press PHONE (on the Handset) or SPKR
(on the Base Unit) to get a dial tone
■ Press MEM and the Memory Location key
(0-9)
B For example, to dial the number you as­
signed to key '8', you would press PHONE,
MEM, 8 (on the Handset), or SPKR, MEM, 8
(on the Base Unit).
TO CHANGE OR REPLACE A STORED
NUMBER
I You can change or replace a stored phone
number by storing a new number in its place.
See TO STORE A NUMBER INTO MEMORY.
TO ERASE STORED NUMBER
FROM MEMORY_________ ^___________
■ The Handset must be OFF.
■ Press PRG/PRV on the Handset.
■ Press the Memory Location of the phone
number to be erased.
■ Press MEM on the handset to complete
programming.
STORING PAUSES IN MEMORY
■ To insert a pause while programming a
Memory Dial number, do the following on the
Handset:
■ Press PRG/PRV on the Handset
■ Press the Memory Location key where the
phone number will be stored (0-9)
■ Dial the number you want to store, press­
ing HOLD at the appropriate point (to insert a
2 second pause). The number can be up to
16 digits long. Each press of HOLD is treated
as stored digit.
■ For longer pauses, press HOLD two or
more times. Each press makes the pause 2
seconds longer and is treated as a stored
digit.
B Press MEM on the Handset to complete ;
programming.
B For example, if your phone is connected to
a PBX, you can store the PBX access num­
ber and a pause before the phone number.
To store 9-PAUSE-555-1234, in Memory Lo­
cation 8, you would:
■ Press PRG/PRV
■ Press 8