Kenmore POWER MISER 153.336951 - Manual (Page 12)

Installation Instructions (cont’d)
Temperature-Pressure Relief Valve
A WARNING
Àt die time of manufacture this water heater was piwided
with a combination temperature-pressures reiief vaive certi­
fied by a nationaily recognized testing iaboratory that main­
tains periodic inspection of production of listed equipment or
materials, as meeting the requirements for Relief Valves and
Automatic Gas Shutoff Devices for Hot Water Supply
Systems, and the latest edition of ANSI Z2I.22 and the code
requirements of ASME. If replaced, the valve must meet the
requirements of local codes, but not less than a combination
temperature and pressure relief valve certified as meeting
the requirements for Reiief Valves and Automatic Gas
Shutoff Devices for Hot Water Supply Systems, ANSI Z2I.22
by a nationally recognized testing laboratory that maintains
periodic inspection of production of listed equipment or
materials.
The valve must be marked with a maximum set pressure not
to exceed the marked hydrostatic working pressure of the
water heater (ISO lbs./sq. in.) and a discharge capacity not
less than the water heater input rate as shown on the model
rating plate. (Electric heaters - watts divided by 1000 x 3415
equal BTU/Hr. rate.)
Your local jurisdictional authority, while mandating the use of
a temperature-pressure relief valve complying with ANSI
Z2I.22 and ASME, may require a valve model different from
the one furnished with the water heater.
Compliance with such local requirements must be satisfied
by the installer or end user of the water heater with a locally
prescribed temperature-pressure relief valve installed in the
designated opening in the water heater in place of the facto­
ry furnished valve.
For safe operation of the water heater, the relief valve must
not be removed from it’s designated opening or plugged.
The temperature-pressure relief valve must be installed
direçtly into the fitting of the water heater designated for the
relief valve. №sition the valve downward and provide tubing
so that ^ discharge virill exit only within 6 inches above, or
at any distance below the structural floor. Be certain that no
contact is made with any live electrical part. The discharge
opening must not be blocked or reduced in size under any
circumstances. Excessive length, over 30 feet, or use of more
thah four elbows can cause restriction and reduce the dis­
charge capacity of the valve.
No valve or other obstruction is to be placed between the
relief v^ve and the tank. Do not connect tubing directly to
discharge dram unless a 6" air gap is provided. To prevent
bodily injury, hazard to life, or property damage, the relief
i^e must be allowed to discharge water in quantities should
circumstances demand. If the discharge pipe is not connect­
ed to a drain or other suitable means, the water flow may
cause property damage.
The Discharge Pipe;
• Must not be smaller in size than the outlet pipe size of the
valve, or have any reducing couplings or other restrictions.
• Must not be plugged or blocked.
• Must be of material listed for hot water distribution.
• Must be installed so as to allow complete drainage of both
the temperature-pressure relief valve, and the discharge
pipe.
• Must terminate at an adequate drain.
• Must not have any valve between the relief valve and tank.
AWARNING
The temperature-pressure relief valve must be manually
operated at least once a year. Caution should be taken to
ensure that (I) no one is in front of or around the outlet of
the temperature-pressure relief valve discharge line, and (2)
the water manually discharged will not cause any bodily
injury or property damage because the water may be
extremely hot
If after manually operating the valve, it fails to completely
reset and continues to release water, immediately close the
cold water inlet to the water heater, follow the draining
instructions, and replace the temperature-pressure relief
valve with a new one.
HOT COLD
temperature -
pressure
RELIEF VALVE
DISCHARGE PIPE
(Do not cap or plug)
AIR GAP
RELIEF VALVE OPENING
At the time of manufacture, this water heater was provided with a combination tem-
peratur^pressurc relief valve listed as compljdng with the standard for relief valves and
automatic gas shut-off devices for hot water supply systems. ANSI Z2I.22. for safe
operation of the water heater, the relief valve must not be removed from its designated
point of installation or plugged.
Your local ¡urisdictional authority, while mandating the use of a temperature-pressure
relief valve complying with ANSI Z21.22 and ASME, may require a valve model different
from the one furnished with the water heater.
Compliance with such local requirements must be satisfied by the installer or end user
of the water heater with a locally prescribed temperature-pressure relief valve installed
in the designated opening in the water heater.
See manual heading -“Temperature-Pressure Relief Valves" for installation and mainte­
nance of relief valve, discharge line, and other safety precautions.
12