beautypg.com

Adanger – Kenmore THE ECONOMIZER 153.33205 User Manual

Page 23

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

background image

TEMPERATURE REGULATION

Due to the nature of the typical gas water heater, the water temperature
In certain situations may vary up to 30°F (16.7°C) higher or lower at the
point of use such as, bathtubs, showers, sink, etc.

Any water heater’s intended purpose is to heat water. Hot water is
needed for cleansing, cleaning, and sanitizing (bodies, dishes, clothing).

Unfempered hot water can presents scald hazard. Depending on the

time element, and the people involved (adults, children, elderly, infirm,

etc.) scalding may occur at different temperatures.

It is recommended that lower water temperatures be used to avoid the
risk of scalding. It is further recommended, in all cases, that the water

temperature be set for the lowest temperature which satisfies your

hot water needs. This wiil also provide the most energy efficient
operation of the water heater.

Figure 26 shows the approximate water temperatures produced at

various thermostat settings. Short repeated heating cycles caused by
small hot water uses can cause temperatures at the point of use to
exceed the thermostat setting by up to 30°F (17°C). If you experience

this type of use you should consider using lower temperature settings
to reduce scald hazards.

Valves for reducing the point-of-use temperature by mixing cold and

hot water are available, see Figure 15. Also available are inexpensive
devices that attach to faucets to limit hot water temperatures. Contact
a licensed plumber or the local plumbing authority.

ADANGER

Water

temperature

over

125°F

(52°C) can cause severe burns
instantly resulting In severe Injury or
death.

Children, the elderly, and the
physically or menially disabled are at
highest risk for scald Injury.

Feel

water

before

bathing

or

showering.

Temperature limiting valves are
available.

Read instruction manual for safe

temperature setting.

HOT WATER CAN SCALD: Water heaters are intended to produce hot

wafer. Water heated to a temperature which wiii satisfy space heating,
clothes washing, dish washing, and other sanitizing needs can scald
and permanently injure you upon contact. Some people are more likely
to be permanently injured by hot water than others. These include the

elderly, children, the infirm, or physically/mentaily handicapped. If anyone
using hot water in your home fits into one of these groups or if there is

a local code or state law requiring a certain temperature water at the
hot water tap, then you must take special precautions. In addition to

using the lowest possible temperature setting that satisfies your hot
water needs, a means such as a mixing valve, shall be used at the hot
water taps used by these people or at the water heater. Mixing valves
are available at plumbing supply or hardware stores, see Figure 15.

Follow manufacturer’s instructions for installation of the valves. Before

changing the factory setting on the thermostat, read the “Temperature
Regulation” section in this manual, see Figure 26.

Never allow small children to use a hot water tap, or to draw their own
bath water. Never leave a child or handicapped person unattended in
a bathtub or shower.

The water heater should be located In an area where the general
public does not have access.

The water temperature setting was factory set at the lowest
temperature; Pressing the “COOLER” Tv) button decreases temperature
and pressing the “HOTTER” (pTf button increases the temperature.

Setting the water heater temperature at 120°F (49°C) (Approx.
mark on temperature setting of gas valve) will reduce the risk of scalds.
Some states require settings at specific lower temperatures.

To avoid any unintentional changes in water temperature settings, the
control has a tamper resistant feature for changing the temperature
setting. To change the temperature setting follow these instructions:

1. “Wake Up” the temperature indicators by holding down both

“COOLER” and “HOTTER” temperature adjustment buttons at the
same time for one second, see Figure 26. One or two of the
temperature indicators wiii light up. These indicators will only remain
on for 30 seconds if no further buttons are pressed. After 30 seconds
the control will go back to “Sleep” mode.

2.

Release both of the temperature adjustment buttons.

a. To decrease the temperature press and release the “COOLER”

button until the desired setting is reached.

b. To increase the temperature press and release the “HOTTER”

button until the desired setting is reached.

NOTE: Holding down the button will not continue to lower or raise the
temperature setting. The button must be pressed and released for
each temperature change desired.

Should overheating occur or the gas supply fail to shut off, turn off the
manual gas control valve to the appliance,

TEMPERATURE INDICATORS

Display

▼ A В C

tm

C-Flashing = approx. 160°F (71 °C)

OOOOO*

About 1/2 seconds

C = approx. 150°F (66°C)

OOOOO*

About 1-1/2 seconds

B = approx. 140°F (60“C)

oooo«o

Less than 5 seconds

A = approx. ISCF (54"C)

ooo#oo

About 30 seconds

▼ = approx. 120“F (49°C)

00*000

More than 5 minutes

WARM = approx. 80“F (27“C)

•OOOOO

FIGURE 26.

23

This manual is related to the following products: