Whirlpool Thin Twin - Manual (Page 6)

I Determine the length of
exhaust duct that is needed to connect the
dryer to the exhaust hood. See "Exhaust
requirements," Panei B.
26
Connect exhaust
duct to washer/dryer
and then to the
exhaust hood.
• Use the straightest path possibie to avoid
90° turns.
• Use duct tape to seai all joints in the
exhaust system.
• Use caulking compound to seai exterior
waii opening around exhaust hood.
27
I CHECK ELECTRICAL
REQUIREMENTS. BE SURE YOU HAVE CORRECT
ELECTRICAL SUPPLY AND RECOMMENDED
EARTHING METHOD.
Check the Installation Instructions to see that
you have compieted each step. Compiete
any missed steps before you continue.
extra part, go back through the steps to see
which step was skipped.
29
(fi
4
Check that you removed aii the
shipping pieces, inciuding the three shipping
straps with keys. Dispose of all materials in
proper manner.
If you do not remove all three shipping
straps, your washer/dryer may “walk” away
from Its location.
Closet installation
I Remove tape from dryer
door and open dryer door. Remove tape
across the dryer lint screen. Check to be sure
lint screen is in its proper position. Wipe out
drum with a damp cloth to remove any dust.
Start dryer and allow it to complete a heat
cycle to make sure the dryer is working
properly.
36
TO PREVENT LARGE AMOUNTS OF LINT AND
MOISTURE FROM ACCUMULATING IN THE
RECESSED AREA, TO MAINTAIN DRYING
EFFICIENCY, AND TO PREVENT EXPOSURE TO
POSSIBLE HEALTH HAZARDS, THIS APPLIANCE
SHOULD BE EXHAUSTED OUTDOORS.
TTris washer/dryer may be installed in a
recessed area or closet.
The installation spacing is in inches and
centimeters and is the minimum allowable.
Additional spacing should be considered for
ease of installation, servicing and
compliance with local codes and
ordinances.
If closet door is installed, the minimum
unobstructed air openings in top and
bottom are required. Louvered doors with
equivalent air openings are acceptable.
Closet installation must be exhausted.
Other installations must use the minimum
dimensions indicated.
I 0 " ( 0 c cm)
Check that you have all your
■ Turn on water faucets and
check for leaks. Tighten couplings if there is
leaking. DO NOT OVERTIGHTEN. This could
cause damage to faucets.
f
12"
(30.5 cm)
32
I Replace the access panel. Be
sure to tighten screws at each end of the
access panel.
33
earthed oi
34
Recessed installation
0" (0 cm)
I Finally, save all literature and
keep with washer/dryer.
You have just
fl(3lshed Installing your
new Whirlpool washer/dryer.
To get the most efficient use from
your new Whirlpool washer/dryer,
read your Use & Care Guide.
Congratulations!
Keep Installation Instructions nearby
where you can refer to them.
They'll make reinstalling your
Whirlpool washer/dryer In
another home as easy as
the first Installation.
Recessed and closet
installation instructions
^WARNING
Fire Hazard
• It Is recommended that the
washer/dryer be exhausted to the
outside.
• If washer/dryer Is Installed In a closet,
the dryer MUST be exhausted outside.
Failure to do so may result In a fire.
Unobstructed air openings are minimum for cioset
door. Louvered door with equivaient air openings
is acceptabie.
Closet installation must be exhausted outdoors.
Recessed, non-exhausted installation must use
only the rear exhaust position and Exhaust
Deflector Kit No. 4500 is required.
Product dimensions
(Shown with legs extended 1 Inch (2.5 cm)
from bottom of washer/dryer.)
(36.2 cm)
recess width
rear view
washer
I Plug power supply cord into
earthed outlet.
I Read the Use and Care Guide
to fully understand your new washer/dryer.
Now start the washer and allow it to
complete the regular cycle.
front view
Minimum Installation spacing
Note: If recessed insfallation is exhausted, all
spacing can be 0 inches (0 cm).
Additional clearance for wall, door and floor
molding may be required.
Panel E