Panasonic PV-M2036 - Manual (Page 17)

Cancel a Tinner Recording:
Recording js in progress
Hold down the STOP button for a few
seconds to cancel the Timer Recording.
• Any future daily or weekly recordings will be
performed as programmed.
Replace Program Contents:
Recording is not in progress
Push the PROG
button to display
all currently
set programs.
Rotate and push
the Wheel to
select and enter
the desired timer
recording.
{See page 16.)
P DT STRAT STOP CH SPD
1 -
3 10 8
4 SU 9
SELECT
HITTER
CANCEL
END
OOp 9:00p 10 SP
OOplOiOOp L SLP
-8:ROTATE WHEEL
PUSH WHEEL
PUSH CLEAR KEY
PUSH PROG KEY
I f START STOP
№1
8 SAT 10:OOP12:OOP125
BY ROTATING WHEEL
■i-PUSH CLEAR :PUSH WHEEL->
TO END PUSH PROG KEY
Rotate and push
the Wheel to select and enter
replacement information.
Push the PROG button to exit this
mode and return to the normal TV
screen.
Review or Clear Program Contents:
Recording is not in progress
P DT STRAT STOP CH SPD
2 a 10:00p12:00p 125 SLP
3 10 8:00 p 9:00p 10 SP
4 SU 9:00p10:00p L SLP
SELECT 1-8:H0TATE WHEEL
ENTER :PUSH WHEEL
CANCEL :PUSH CLEAR KEY
END : PUSH PROG KEY
Push the PROG
button to display
all currently set
programs.
Rotate the Wheel
to select the
desired program
number.
Push the CLEAR
button to clear the
program.
Push the PROG button to exit this
mode and return to the normal TV
screen.
P DT STRAT
□-----------
2 8 10
3 10 3
4 SU 9
STOP CH SPD
OOp 12;00p 125 SLP
OOp 9-.OOp 10 SP
OOp 10:00p L SLP
SELECT 1-8:R0TATE WHEEL
ENTER :PUSH WHEEL
: PUSH PROG KEY
Timer Recording
Using Unit Buttons
A timer recording can be set up using the buttons on the
Combination VCR. If necessary, the clock can also be set.
Hold down
REC/TIME.
and
Push FF to
enter the
program mode.
START STOP CH
SLP
SELECT START DATE
BY SELECT i/T KEY
NEXT, PUSH SET KEY OR
TO END PUSH PROG KEY
• If the clock is not set, pushing
these buttons will display the SET
CLOCK screen. In this case, set
the clock according to the OSD’s
instructions and then set a timer
recording.
• Once the Combination VCR is in the Program mode, the
PLAY, REC, FF, and REW buttons on the Combination
VCR operate only as specified above.
SET CLOCK --------------
EtnSSKISi
MANUAL SET
SELECT : PUSH SELECT A/T
SET ; PUSH SET KEY
END : PUSH PROG KEY
or
Push REW or PLAY to
make your selection.
(for down) (for up)
Push FF to set
and move on to
the next item.
Push SET (FF) repeatedly to move to a
particular item for setting or correction.
Items to be Set:
• recording DATE
• START time
• STOP time
• CH(annel), or LINE
• SPEED (SP, LP. SLP)
When the program is completed...
and [E]
Push RECATIME
and FF to display
program contents.
(at the same time)
To set the next program,
repeat steps 2, 3, and 4 before continuing with step 5.
and I ►►
Push REC/TIME and
FF to exit this mode.
(at the same time)
It is not possible to clear a timer program using the Combination
VCR buttons. Please use the Remote Control.
17