Panasonic SL-SW851C - Manual (Page 5)

Anti-Shock Function
Anti-shock works by reading audio data and storing it in
memory (up to 40 seconds worth). The unit then tiiis in
internjptions caused by bumps and vibrations with data
(rom the memory. This unit aiso incorporates a powerful
anti-shock mechanism that prevents skipping caused
when play speed is changed by swinging of the unit.
1
Press during stop mode.
О
The following indicator appears on the display panel.
Alter about
20 seconds
About
5 seconds later
The jogger display
starts (lastmg.
1223
Wait until the jogger display is shown before starting to
jog-
When bumps continue repeatedly
The following indicator appears on the display panel
and sound is interrupted.
The jogger display can also flash or go out under the fol­
lowing coTKlttions:
•As the end of the last track approaches,
•As the end of a track approaches during random play, pro­
gram play, and 1 track repeat play,
• If the track in play or ne>ct track is extremely short.
To cancel the anti-shock function
Press [A.SHOCK] again.
i?T!ra
•The anti-shock setting can be changed during play,
but this may cause a slight interruption in the sound
because the disc's rotational speed changes.
• During anti-shock operation, the disc rotates at a high­
er rate than usual in collecting extra audio data. This
could result in a slight increase in disc rotation noise.
Using the unit with an audio system
The anti-shock function uses digital signal conpression
technology. It is recommended that the anti-shock func­
tion be canceled if the unit is connected to a home
audio system.
Using Stereo Headphones with Remote Control
SL-SW870 ONLY
The remote control can be operated regardless of the
hold mode of the unit.
Before operation, be sure to release hold.
Operation confirmation tones
When an operation button is pressed, a confirmation
tone sounds. Refer to the parentheses in the illustra­
tion for the different types of confirmation tones.
Using the Unit with Optional Accessories
Using the unit with an audio system
Using a stereo connection cable (not included), you can listen to
CDs through your audio systent.
•Connect the cable to the amplifier after turning oft its power.
• Do not connect the cable to the PHONO jacks on the amplifier.
•Obtain the optional connecting cable if the amplifier comes with
mini-phone jacks.
•Adjust the volume level on the amplilier.
I SL-SWB70 ONLY |
You can connect speakers, active or otherwise, with an
impedance of Ikil or less to the headphone jacks. Set
the unit's volume between 4 and 6.
rna
Sound quality changes when S-XBS or VMSS(SL-SW870 only) is
selected, but volume is reduced by approximately fifty percent.
Using the unit with a car audio
system
SL-SW851C comes with a car adaptor and car stereo
cassette adaptor.
Items to be purchased
(SL-SW870/SL-SW850)
For connection to the car audio system;
Car stereo cassette adaptor (SH-CDMIOA)
Connect the car stereo cassette adaptor ‘
to the unit’s headphone jack.
>
(When doing this, keep the unit’s VOLUME
controi at a setting between 5 and 8.)
For securing the unit and connecting the
power suppiy;
•Car adaptor (SH-CDC9)
•Car mounting kit (SH-CDF20)
Car mounting arm, Car insulator
СБО
It may not be possible to use the unit with some types of
car stereo owing to restrictions imposed by the con­
struction of the car stereo cassette adaptor.
For further details, refer to the instructions of the part
concerned.
Maintaining the
Lens
Open the ltd and clean the lens as shown in the figure.
Use a cotton swab to gently wipe off any finger-prints.
Recommended product: Lens cleaner kit (SZZP1038C)
RQT5062