Panasonic TOUGHBOOK CF-28 - Manual (Page 25)

10 At the confirmation message , press Œ).
The computer will reboot, and the operation of reinstalla­
tion for the hard disk starts automatically.
CWinaSwsiiSl
After the “restore” procedure completes, a message will
be displayed. Remove the Product Recovery CD-ROM,
then close the tray.
(T)Turn the computer off and remove the CD drive.
@Set the floppy disk drive in the multimedia pocket and
put the FIRSTAID FD into the floppy disk drive, then
turn the computer on.
Follow the on-screen instructions.
4Wir^Q^2'OjOO)M4Win30^
When the message “insert the next CD” is displayed, in­
sert the Product Recovery CD-ROM showing the next
number in the sequenee, and then select [OK].
(In the case of Windows NT, only Product Recovery CD-
ROMs 1 and 2 can be used.)
{ note )--------------------------------------------------s
If [OK] is not immediately selected:
The message “The media does not contain the correct
file” may appear. When [OK] is selected, the message
“insert the next CD” will be displayed again.
Confirm that the proper Product Recovery CD-ROM
has been inserted by opening the tray of the CD drive
and then close the tray, then immediately select [OK].
11 After the reinstallation procedure completes, the follow­
ing message will appear on the display. Remove the floppy
disk or Product Recovery CD-ROM, then restart the com­
puter by pressing ( Ctrl
) -I- [ Alt ) -i- C Pel ).
4Winclow^98l
All data on the whole HDD has been restored to the factory default.
After removing floppy disk, restart the computer and set up Windows
again.
4WirK)owsf2W0>
Windows 2000 install wizard will start after reboot.
Restore process will execute more after Windows 2000 install wizard.
Restart the computer after removing Product Recovery CD-ROM,
4Wii^ow^NJ#
Windows NT4.0 install wizard will start after reboot.
Restore process will execute more after Windows NT4.0 install
wizard.
Restart the computer after removing Product Recovery CD-ROM.
12 When the message [Press to enter SETUP] is dis­
played, press ( F2 ) and then run the Setup Utility.
If the password has been set, enter the Supervisor Pass­
word.
13 Press
At the confirmation message, select [Yes] and press
C Enter ]. (The Setup Utility settings will return to their
default values. Even the security settings with the excep­
tion of the password(s) will return to their default values.)
A^ note >
If there are added functions that are not listed in the
Specifications of this Operating Instructions, we rec­
ommend disabling their device settings. If the settings
are enabled, additional operations may be necessary
during the Windows setup procedure. (We also rec­
ommend referring to the Supplementary Instructions,
if they are included with the computer.)
14 Using e i t h e r o r
0
, select [Exit] and then select
[Save Current Values], then press (Enter).
At the confirmation message, select [Yes] and press
t Enter).
15 Powder off your computer.
16 Perform the setup procedure for Windows by following
the instructions on the screen.
(Refer to the Supplementary Instructions, if they are in­
cluded with the computer.)
Page 11
C3"Page 12
77 Run the Setup Utility and change the settings where nec­
essary.
4Windowsl98l
4Wincl0^2W0mWinaQwsII^T*
A note >
When the message [Operating System not found] is
displayed, press rbtrD + f A i t ) + fPiD
and perform the operations from Step
12 to Step 14.
If you fail to press ( F2 ) in Step 12 , restart the com­
puter and perform the operations from Step 12 to Step
14 after finishing Windows setup procedure.
25