Panasonic NV-J35 - Manual (Page 13)

Setting the Clock to the Present Time Using the Bar
Codes
0
d
9
? ?
mm
I iiH K m ____ _ * ..
I IM s Mt 1 OMMW IMM ::: 111 n IM a IH
X m n nil 4 o HIM ■ □ raw i: M ■ HI ■ lil
3 m I nil r z; giHI ' = «111 n m a NM 1 1«
3! iin 1 an • □ MIW 1 D IHW HI a HI 3 M
IW £ na 1 = Hnu • = IHW T ini I im a IIH
:i: nni 1 IK <0 mm Mm I MM I IIH a Ml
I IMI a iiH MM 11 D IHW ^ HI a HI I Ml
I Mi I MU tz iHM •C IHW a IM 1 NN a im
3 m I un tD llWI *2 %wm I IM a IIH a Ml
IM s HI niHt * 2 MM a «N a III a am
z IM e IW ■ IMHI IH a nil e im
] lilt ■ MM ■ o §m •C |iM» 1 IM am a IN
3 iHi a iw «D nni » 2 niw a IIH a iiN a iM
I HU a III!
II nn
n HM
0 IlMt
0 IIIW
a »M
3 llil a ail a HI
1 HM a HU a IM
1 m a Ml ■ IIH
\ - □ MM C INN :: M a Hii ■ wi
|a m i:: HM c mw a IIH a IM a nil
■ IW D IW
IW C IINI
c raw
C IIIW
] IIH a IIN a MH
a nu a HH
I m ..H
3 IlM DM
lina
c UWI
c liMI D I'MW
= M c: UN :: Mi
t III! z; MW 2 niW
SIS* 3-3=1*
- ll' ______________________ _______ 1
me HI III z II
•C IM »n II I vll
-i: til ■- ‘M I iH
•mZ III mC in z III
>i*= III ■>: III 1 'IW
mZ 'in -C ll> I 'IK
■«Z !|I1 mZ UN z til
™iC HI mZ 11 I III
>•: tin mZ ill V III
»1 1*1 -Z IM T II
!«■= HI! nz lU Z Ml
mZ IM ^ ni
e o
Preparation
• Slide down the Mode Selector Cover on the Remote
Controller so that the Bar Code Reader Display can be
seen.
• Press the Digital Scanner On/Off Button to “ON”.
Q Trace the bar code “SETTING OF THE CLOCK”.
SETTING OF THE CLOCK
&
0 Trace the bar code for the year (YEAR).
0 Trace the bar code for the month (MONTH).
0 Trace the bar code for the day of the month (DATE),
0 Trace the bar code for the hour (START TIME).
START TIME
1 n n
t'UU 9 B-
0 Trace the bar code for the minute (MIN),
MIN
5 - n ~ l
t u
m
0 Press the Transmit Button on the Remote Controller
and then confirm that the time is displayed in the
Multi-Function Display of the VTR.
0 Press the Digital Scanner On/Off Button to “OFF".
• If the transmission was not received correctly, the
“Beep-Beep, Beep-Beep” sound from the VTR will warn
you. In this case, perform transmission again.
• If the Remote Controller is ¡eft with no operation per­
formed for more than 4 minutes, it will automatically
switch over to the power-saving standby condition and the
lamp in the reading tip goes out. In this case, bar codes
that have already been read (but not yet transmitted to the
VTR) will be cancelled.
•The bar codes “SETTING OF THE CLOCK”. “YEAR” and
“MONTH” are located on page 3 of the Programming
Sheet.
<1 DATE
13)