OFNA Racing 91849 DigiPeak 3 - Manual (Page 3)

Plug the charger into an AC 110V/230V wall outlet or a DC 12V power source. The
charger power is on now and the LCD displays the MAIN MENU.
The LCD displays the data below.
If you need to stop charging, press the S(START) button to stop it, and then press
the START button to go back to the MAIN MENU.
* When the battery pack is fully charged or discharged, you can press the
S(START) button to RE-PEAK or RE-DISCHARGE the pack.
* After the battery pack has peaked, press the (ENTER) button, the LCD will
show MAX. voltage during charging.
* If the battery pack is not connected to the charger before
charging, the LCD will show an ERROR massage.
* If the cell number you selected does not match the battery pack,the LCD will show
an ERROR massage in Li-Po or Pb mode.
* If the cell number you selected is not coincident to the Li-Po or PB battery pack,
the LCD display will show an Error message.
1.When the number of the battery pack>select number, the LCD
display will show "[Error] OVER VOLTAGE".
2.When the number of the battery packcharger will charge battery pack at 0.3A about for 2 min..If the battery voltage is still over low, the LCD display willshow "[Error] LOW VOLTAGE".1.Using the + (INCREASE) / -(DECREASE) button to select the battery type youwant and connect the charge lead of the charger to the connector of the batterypack..2. Then, press the(Enter) button into the mode you selected .NI-CD CHARGEC=2.OA1234[Error]OVER VOLTAGE[Error]OPEN CIRCUIT[Error]LOW VOLTAGECHG 00 : 00 00000NC+ 2.00A xx. xxV1234567ABCDFunction ButtonOperation SignalINCREASE+DECREASE-ENTER
STARTSFLASH''1:Battery type2:Charge status3:Charge current4:Cell count(Li-Po & Pb only)1:The charger is in the charge condition(CHG:Fast Charge/DHG:Discharge)2:Time (sec)3:Capacity(mAh)4:Battery type5:Charge status setting(+:Fast Charge-:Discharge*:Charge after Discharge )6:Charge / Discharge rate7:Battery Voltage(V)NI-CD CHARGEC=2.0ANI-MH CHARGEC=2.0ALI-PO CHARGEC=2.0A7.4VTONE ENABLEPB CHARGEC=2.0A12.0V+++++-----3Operation InstructionMain Menu Pages: 1 2 3 4 5 6 7 wrong Brand wrong Model non readable See also other documents in the category OFNA Racing Hardware: Force .12 S & .15 S (2 pages) Force .15 R (2 pages) Force .21 P4, Black T8 (3 pages) Force .25 & .26 (2 pages) Force .28 (2 pages) Force .32 (2 pages) Hyper .18 (2 pages) Hyper .21 (4 pages) JL .21 Pro (3 pages) Picco .12 R, 3 or 7 Port (4 pages) Picco .21 01 BP, SG Shaft (4 pages) Picco .21 Boost (3 pages) Picco .21 Comp (4 pages) Picco .21 MAX (2 pages) Picco .21 Sport (4 pages) Picco .26 Big Block (3 pages) Picco .26 MAX (2 pages) Picco .26 MAX JL Red Dot (2 pages) Picco .28JL Team Turbo (3 pages) 2-Speed, Cam (3 pages) 2-Speed, Shoe, OB4 1/10th Scale (2 pages) New Differential Case, K-Style, 1/8th Scale (1 page) 91850 - Charger (2 pages) Ho Bao RTR Radio (9 pages) 2-Speed, Shoe (4 pages) 2-Speed, Shoe, Z-10 (2 pages) Torsen Differential - Center (1 page) PCR Laydown Servos (1 page) 2-Speed, Shoe, HPI & Z10 - 1/10th Scale (3 pages) Buggy Pivot Ball Kit (2 pages) Torsen Differential - Front & Rear (1 page) 9.5 2-Speed Trans Assembly (3 pages) 2-Speed, Shoe, HPI 1/10th Scale (2 pages) GTP Conversion Kit (6 pages) Wheel Setup (1 page) 91850 - Charger 1-14 Cell (2 pages) 19240 - 2-Speed Transmission for Hyper 7 Series (1 page) 2-Speed, Shoe, OB4 Long 1/10th Scale -- 35017 (5 pages) GTP Rear Pivotball & Anti-roll Kit -- 31296 (3 pages) 92135 - Power Supply, 7 AMP (1 page) 40991 Hong Nor RTR Radio (11 pages) Sitemap
charger will charge battery pack at 0.3A about for 2 min..
If the battery voltage is still over low, the LCD display will
show "[Error] LOW VOLTAGE".
1.Using the + (INCREASE) / -(DECREASE) button to select the battery type you
want and connect the charge lead of the charger to the connector of the battery
pack..
2. Then, press the (Enter) button into the mode you selected .
NI-CD CHARGE
C=2.OA
1 2
3
4
[Error]
OVER VOLTAGE
[Error]
OPEN CIRCUIT
[Error]
LOW VOLTAGE
CHG 00 : 00 00000
NC+ 2.00A xx. xxV
1
2
3
4
5
6
7
A
B
C
D
Function Button Operation Signal
INCREASE +
DECREASE -
ENTER
START
S
FLASH ' '
1:Battery type 2:Charge status
3:Charge current 4:Cell count(Li-Po & Pb only)
1:The charger is in the charge condition
(CHG:Fast Charge/DHG:Discharge)
2:Time (sec)
3:Capacity(mAh)
4:Battery type
5:Charge status setting(+:Fast Charge
-:Discharge * :Charge after Discharge )
6:Charge / Discharge rate
7:Battery Voltage(V)
NI-CD CHARGE
C=2.0A
NI-MH CHARGE
C=2.0A
LI-PO CHARGE
C=2.0A 7.4V
TONE ENABLE PB CHARGE
C=2.0A 12.0V
+
+ +
+ +
-
-
-
- -
3
Operation Instruction
Main Menu