Pilgrim Pressure Regulators Type 51 - Manual (Page 4)

ORDERING
INFORMATION
PART NUMBER:
REGULATOR
OPTIONS &
ACCESSORIES
NON RELIEVING
Used in applications where it is desir-
able to relieve pressure downstream
and not at the regulator. Non-reliev-
ing regulators should not be used for
low or no flow applications.
KNOB
Replaces the standard square head
adjusting screw. (except T-51FRCT)
5 MICRON FILTER
Replaces the 40 micron filter for
more complete air filtration. (Except
T-51R)
EPOXY FINISH
An epoxy paint applied to the body
and dripwell of the regulator exterior
surfaces to provide increased
corrosion resistance. (Standard for
T-51FRCT)
MOUNTING BRACKET
Plated steel bracket for side mount-
ing. (316 SS for T-51FRCT)
COALESCING FILTER
Replaces the 40 micron filter for
both moisture and particulate filtra-
tion. (T-51AFR only)
LT 0795 5m 5/02
SALES & APPLICATIONS
(800)727-5646 fax:(304) 387-4417
w w w. m a r s h b e l l o f r a m . c o m
IMPORTANT NOTICE
Our recommendations, if any, for the use of this product are based on
tests believed to be reliable. The greatest care is exercised in the selec-
tion of our raw materials and in our manufacturer, no guarantee or war-
ranty, express or implied is made as to such use or effects incidental to
such use, handling or possession or the results to be obtained, whether in
accordance with the directions or claimed so to be. The manufacturer
expressly disclaims responsibility therefor. Furthermore, nothing con-
tained herein shall be construed as a recommendation to use any product
in conflict with existing laws and/or patents covering any material use.
PRESSURE GAUGE
Dual scale (psi/kPa) 2” (50mm)
gauges. Ranges include 0-60 psi (0-
4.1 BAR),0-100 psi (0-6.9 BAR) and
0-120 psi (0-8.3 BAR). When speci-
fied with regulator, the correct range
will be supplied.
FLUOROCARBON ELASTOMERS
Diaphragm, as well as gaskets and
O-rings, are made with a special
elastomer to prevent deterioration
from elements in the air supply, such
as flame retardant synthetic lubri-
cants normally destructive to the
standard BUNA-N material.
TAMPER PROOF COVER
A 316 stainless steel hexagonal cover
placed over the adjusting screw and
threaded onto the bonnet of the regu-
lator with a wrench, prevents ordinary
hand adjustments. Supplied with an
O-ring that is designed to seal the
adjusting screws threads in captured
bleed applications. (T-51FRCT Only)
LOW BLEED DIAPHRAGM
(Soft Relief Seat): Used in applica-
tions where it is desirable to minimize
the standard bleed rate of the
regulator while maintaining the ability
to relieve excess pressure at the
regulator. Bleed rate is reduced from
less than 6 SCFH (2.8 LPM) to less
than 0.1 SCFH (0.05 LPM).
(T-51FRCT only)
USA EUROPE
State Route 2, Box 305 9 Castle Park, Queens Drive
Newell, WV 26050 Nottingham NG2 1AH, UK
800- 727-5646 or (304)387-1200 Tel +44 (0) 115 993 3300
FAX (304) 387-4417 Fax +44 (0) 115 993 3301
[email protected] [email protected]
Part Control Range
TYPE Number psig BAR
960-222-000 0-30 0-2.1
51R 960-223-000 0-60 0-4.1
960-224-000 0-100 0-6.9
960-175-000 0-30 0-2.1
51FR 960-176-000 0-60 0-4.1
960-177-000 0-100 0-6.9
960-284-000 0-30 0-2.1
51AFR 960-285-000 0-60 0-4.1
960-286-000 0-100 0-6.9
960-303-000 0-30 0-2.1
51 FRCT 960-304-000 0-60 0-4.1
960-305-000 0-120 0-8.3
OPTION ORDERING MATRIX:
Add three digits from table below to end of part number.
OPTION 1 2 3 4 5 6 7 8 9 10 11
1 Fluorocarbon
001 021 031 041 051 061 071 081 091 101 111
Pintle
2 Non-Relieving 002 032 042 052 062 072 082 092 112
3 Knob
003 043 053 063 073 083 103 113
4 5 Micron Filter 004 054 064 074 084 094 104 114
5 Epoxy Coating 005 065 075 085 095 105 115
6 Coalescing Filter
006 076 086 096 106 116
(T-51AFR only)
7 Mounting Bracket 007 087 097 107 117
8 Pressure Gauge 008 098 108 118
9 Tamper-Resistant Cover
009 109 119
Panel mounting Nut
10 Soft Relief Seat
010 110
Low Bleed
11 Fluorocarbon
011
Diaphragm
TYPE-51 GENER
AL P
URPOSE REGUL
A
TORS