Pilgrim Pressure Regulators Type 70 User Manual
Type-70 high fl ow regul ators, Regulator options & accessories, Option ordering matrix
REGULATOR OPTIONS &
ACCESSORIES
NON-RELIEVING
Used in applications where it is desirable to relieve pressure
downstream of the regulator, for some constant flow applica-
tions, and where the gas flowing through the regulator must not
escape at the regulator. Non-relieving regulators should not be
used for low or no flow applications.
CORROSIVE RESISTANT EPOXY FINISH
An epoxy paint applied to the body and dripwell of the regulator
exterior surfaces to provide increased corrosion resistance.
TAPPED VENT
Allows installation of plumbing to capture exhaust air.
MOUNTING BRACKET
Steel (dichromate finish) bracket for side mounting.
PRESSURE GAUGE
Dual scale 2 in. (50.8 mm) gauges. Ranges include 0-30 psig
(0-200 kPa), 0-60 psig (0-400 kPa), 0-100 psig (0-700 kPa) and
0-160 psig (0-1100 kPa). When specified with regulator, the
correct range will be supplied.
TAMPER-RESISTANT COVER
An aluminum tubular cover placed over a slotted head adjusting
screw and screwed onto the bonnet of the regulator with a
wrench. Prevents ordinary hand adjustments.
LOW BLEED
Reduces steady-state air consumption by approximately 50%.
CHECK VALVE
Allows quick dumping of output line pressure through the
supply air line when the supply is shut down.
LT 0805 3m 2/04
SALES & APPLICATIONS
(800) 727-5646 fax: (304) 387-4417
www.mar shbellofr am.com
IMPORTANT NOTICE: Our recommendations, if any, for the use of this product are based on tests believed to be reli-
able. The greatest care is exercised in the selection of our raw materials and in our manufacturer, no guarantee or war-
ranty, express or implied, is made as to such use or effects incidental to such use, handling or possession or the
results to be obtained, whether in accordance with the directions or claimed so to be. The manufacturing expressly
disclaims responsibility therefor. Furthermore, nothing contained herein shall be construed as a recommendation to
use any product in conflict with existing laws and/or patents covering any material use.
USA
EUROPE
State Route 2, Box 305
9 Castle Park, Queens Drive
Newell, WV 26050
Nottingham NG2 1AH, UK
800-727-5646 or (304) 387-1200
Tel +44 (0) 115 993 3300
FAX (304) 387-4417
Fax +44 (0) 115 993 3301
OPTION ORDERING MATRIX:
Add three digits from table below to end of part number.
OPTION
2
3
5
6
7
8
9
10
11
2
Non-Relieving
002 032 052 062 072 082 092
112
3
Sq. head Adj. Screw
003 053 063 073 083
103 113
5
Epoxy Coating
005 065 075 085 095 105 115
6
Tapped Vent
006 076 086 096 106 116
7
Mounting Bracket
007 087 097 107 117
8
Pressure Gauge
008 098 108 118
9
Tamper-Resistant Cover
009 109 119
10 Low Bleed
010 110
11 Check Valve
011
TYPE-70 HIGH FL
OW REGUL
ATORS
Port
Size
Set Point Range
Part Number (NPT)
BAR
psig
T-70
960-129-000
1/4"
0-0.1
0-2
960-174-000
3/8"
0-0.1
0-2
960-162-000
1/2"
0-0.1
0-2
960-130-000
1/4"
0-0.7
0-10
960-131-000
3/8"
0-0.7
0-10
960-163-000
1/2"
0-0.7
0-10
960-089-000
3/8"
0-2.1
0-30
960-090-000
1/4"
0-2.1
0-30
960-159-000
1/2"
0-2.1
0-30
960-091-000
3/8"
0.1-4.1
1-60
960-092-000
1/4"
0.1-4.1
1-60
960-160-000
1/2"
0.1-4.1
1-60
960-093-000
3/8"
0.1-10.3
2-150
960-094-000
1/4"
0.1-10.3
2-150
960-161-000
1/2"
0.1-10.3
2-150
960-152-000
1/4"
0.2-13.8
3-200
960-153-000
3/8"
0.2-13.8
3-200
960-164-000
1/2"
0.2-13.8
3-200
T-70BP
960-191-000
1/4"
0-0.1
0-2
960-192-000
3/8"
0-0.1
0-2
960-194-000
1/4"
0-0.7
0-10
960-195-000
3/8"
0-0.7
0-10
960-197-000
1/4"
0-2.1
0-30
960-198-000
3/8"
0-2.1
0-30
960-200-000
1/4"
0-4.1
0-60
960-201-000
3/8"
0-4.1
0-60
960-203-000
1/4"
0-10.3
0-150
960-204-000
3/8"
0-10.3
0-150
OPTIONS
•
= option is available
s = standard
Type
70
70BP
2
Non-Relieving
•
3
Knob
s
s
Sq. Head Adj. Screw
•
•
5
Epoxy Coating
•
•
6 Tapped
Vent
•
7
Mounting Bracket
•
•
8
Pressure Gauge
•
•
9
Tamper - Resistant Cover
•
•
10 Low Bleed
•
11 Check Valve
•