Wilbur Curtis ALPHA 6GTN - Manual (Page 3)

3 2
Cold Brew Lock . . . (Factory set to 15º) Press  to select, < or > to select desired setting (CBL 5, 15 or OFF),  to set.
The Cold Brew Lock feature allows the brewer to brew at three different temperature levels from the actual set point. The first setting is within 5 degrees of set
point, next is within 15 degrees of set point, OFF is within 30 degrees of set point for the Ready to Brew message, however it will brew at any temperature.
This feature will operate after initialization to set temperature after the rear standby toggle switch is reset to ON.
Master Reset Press  to display Are You Sure? Then < for Yes, > for No. Brewer factory defaults are then reset.
Service Call (Phone number Factory set to [800] 995-0417) Press  to display number and change number or < to move place and EX to exit when
complete This number will be displayed during a Heating system SENSOR ERROR or during a WATER ERROR.
Access Code (Factory set to 1-2-3-4) Press  to display number and change number, (the number can be change 1 to 4) or < to move place and ex to exit
when complete.
Banner Name (Factory set to CURTIS) Press  to display letters and change letters or < to move place and EX to exit when complete. This feature allows
up to 14 letters to be programmed for company name or regional name. Programming all blanks disables Banner Name.
Warmers Auto OFF (Factory set to Disable) Press  to Select. Press < or > to move to desired time and then  to set. Timer is programmable from 2 to 4
hours in one hour increments or OFF.
P-Maintenance (Factory set to OFF) Press  to Select, Set gallons brewed to indicate P-Maintenance. Press < or > to adjust from Off to 3000 gallons.
Press  to exit.
Beeper On/Off (Factory set to ON) Press  to display ON or OFF. Pressing either < or > toggles between on and off.  to set.
Pulse Brew (Factory setting OFF) Press  to select, < or > to select OFF or one of five pulse patterns (A to E) .
Guidelines for Pulse Brew:
This feature allows tuning of the coffee flavor. The pot level should always be set first with this option OFF. Depending on your grind profile and water conditions,
the five Pulse Brew options help “tune” or change the coffee flavor. Filter Pack type coffees typically extract better with the A and B pulse setting. Decaffeinated
coffees typically extract better with the B pulse setting. High-Yield coffees typically extract better with the C pulse setting. Of course, any of the A, B or C settings
may be used to suit your taste profile. There are two additional settings (D and E) that allow you to manually set the ON TIME pulses and OFF TIME.
If Pulse Brew is selected (ON), Cold Brew Lock is set to Delta 1 within 5ºF of set point and Cold Brew Lock disappears from the list of program selec-
tions. When Pulse Brew is ON, Pre-infusion disappears from the list of program selections.
Display Brew Time (Factory set to ON). Press  to display ON or OFF. Pressing either < or > toggles between on and off.  to set. When on, the Display
Brew Time feature allows you to see the remaining time in the brewcyle counting down.
Drip-Out Mode (Factory set to 2 min) Press  to select. Press > to increase time (to a maximum of 5 minutes) or < to decrease the time and turn OFF.
Time counts up in 5 second increments. Press  to set.
Model Select Press  to select, < or > to select model. The selections are: ALPHA-1, ALPHA-2, ALPHA-3/4/5, Airpot Brewer, Thermo-Alpha (for the D60GT).
Press  to set. When the Model Select feature is changed, all settings are reset to the defaults of the newly selected model.
Exit Press  to select, exits program mode and returns unit to operation.
Warmer Temperature Control
Turn on brewer at the control panel ON/OFF button. Warmer button should be OFF (LED off). Press and hold desired WARMER button. Screen will display cur-
rent setting in % of power. Press < or > to increase or decrease power to warmer (50% to 100% in 10% increments). Press  to set.
Tank Temperature Check
Turn on brewer at the control panel ON/OFF button. Press and hold 3 button (see illustration, page 2) for 5 seconds. Water Temperature will be displayed.
The temperature will not display while the unit is in the process reheating.
NOTE: Alpha 3GT ONLY; when checking tank temperature, first make sure REAR warmer is ON (red LED on) and then press 3 for 5 seconds to display
tank temperature.
Brew Volume – Easy Access
Units produced beginning January 2008 can be easily adjusted from the front panel. Written into the software on the Alpha GT UCM, is a feature to access the
brew volume without entering the program mode.
The UCM must be on. To adjust the ALP1GT models, press and hold down the center, Select button 2 . The screen will read
pressing < or >
will adjust the brew volume up or down, ± 20 oz, in 1 ounce increments.
On any multi-station Alpha (ALP2/3/4/5/6GT): Press the center Select button 2 twice, with the second press hold down the button for around five [5] seconds.
The screen will display pressing < or > will adjust the brew volume up or down, ± 20 oz, in 1 ounce increments.
Vol. Adj. < -0 > Oz.
- Select +
Vol. Adj. < -0 > Oz.
- Select +
PROGRAM MENUS