Clarion DXZ646MP - Manual (Page 9)

280-8047-00
DXZ646MP
13
English
Adjusting the Z-Enhancer Plus
1. Press the [Z+] button and select the Z-En-
hancer Plus mode to adjust.
2. Press the [A-M] button and turning the
[ROTARY] knob clockwise adjusts in the +
direction; turning it counterclockwise adjusts
in the – direction.
●When “B-BOOST 0” selected, you can ad-
just the bass in the range of –3 to 3.
●When “IMPACT 0” selected, you can
adjust the bass and treble in the range of
–3 to 3.
●When “EXCITE 0” selected, you can adjust
the bass and treble in the range of –3 to 3.
∗ When Z-Enhancer Plus is selected, press and
hold the [Z+] button for 1 second or longer to
change to the “CUSTOM” mode.
Bass/treble characteristics become flat and
the indication “Z+ FLAT” is shown in the dis-
play.
Adjusting the tone
Press the [A-M] button and select the item to
adjust. Each time you press the [A-M] button,
the item changes as following order:
●When “BASS BOOST” is set
“SW-VOL 0” ➜ “B-BOOST 0” ➜ “BAL 0” ➜
“FADER 0” ➜ Last function mode.
●When “IMPACT” is set
“SW-VOL 0” ➜ “IMPACT 0” ➜ “BAL 0” ➜
“FADER 0” ➜ Last function mode.
●When “EXCITE” is set
“SW-VOL 0” ➜ “EXCITE 0” ➜ “BAL 0” ➜
“FADER 0” ➜ Last function mode.
●When “CUSTOM” is set
“SW-VOL 0” ➜ “BASS” ➜ “TREBLE” ➜
“BAL 0” ➜ “FADER 0” ➜ Last function
mode.
●When “Z+ OFF” is set
“SW-VOL 0” ➜ “BAL 0” ➜ “FADER 0” ➜
Last function mode.
∗ If subwoofer function is set “ON”, “SW-VOL 0” can
be selected.
Adjusting the subwoofer output
volume
You can adjust the volume output from the unit’s
subwoofer output terminal.
1. Press the [A-M] button and select
“SW-VOL 0”.
2. Turning the [ROTARY] knob clockwise
increases the output volume; turning it
counterclockwise decreases the output
volume.
∗ The factory default setting is “0”. (Setting range:
–6 to 6)
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the bass (Gain,
Frequency, Q-curve)
This adjustment can be performed when the Z-
Enhancer Plus is set to “CUSTOM”.
1. Press the [A-M] button and select “BASS”.
2. Turning the [ROTARY] knob clockwise em-
phasizes the bass; turning it counterclock-
wise attenuates the bass.
∗ The factory default setting is “B
Е Е Е Е Е GAIN 0 О О О О О ”.
(Adjustment range: –6 to +8)
3. Press the [ a] or [d] button to select
“B Е Е Е Е Е FREQ 50 О О О О О ”.
Turn the [ROTARY] knob clockwise or coun-
terclockwise to select the frequency.
∗ The factory default setting is “B
Е Е Е Е Е FREQ 50 О О О О О ”.
(Adjustment 50/80/120 Hz)
4. Press the [ a] or [d] button to select “B
Е Е Е Е Е Q 1 О О О О О ”.
Turn the [ROTARY] knob clockwise or coun-
terclockwise to select the Q-curve.
∗ The factory default setting is “B
Е Е Е Е Е Q 1 О О О О О ”.
(Adjustment 1/1.25/1.5/2)
5. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the treble (Gain,
Frequency)
This adjustment can be performed when the Z-
Enhancer Plus is set to “CUSTOM”.
1. Press the [A-M] button and select “TREBLE”.
2. Turning the [ROTARY] knob clockwise em-
phasizes the treble; turning it counterclock-
wise attenuates the treble.
∗ The factory default setting is “T
Е Е Е Е Е GAIN 0 О О О О О ”.
(Adjustment range: –6 to +6)
3. Press the [ a] or [d] button to select
“T Е Е Е Е Е FREQ 12K О О О О О ”.
Turn the [ROTARY] knob clockwise or coun-
terclockwise to select the frequency.
Basic Operations
03.12.26, 5:02 PM Page 13