Motorola SX709 - Manual (Page 2)

CTCSS Code Table
Code Hz Code Hz Code Hz Code Hz
1 67 11 97.4 20 131.8 30 186.2
2 71.9 12 100 21 136.5 31 192.8
3 74.4 13 103.5 22 141.3 32 203.5
4 77 14 107.2 23 146.2 33 210.7
5 79.7 15 110.9 24 151.4 34 218.1
6 82.5 16 114.8 25 156.7 35 225.7
7 85.4 17 118.8 26 162.2 36 233.6
8 88.5 18 123 27 167.9 37 241.8
9 91.5 19 127.3 28 173.8 38 250.3
10 94.8 29 179.9
CDCSS Code Octal Table
Code Octal Code Octal Code Octal Code Octal
39 023 60 143 81 315 102 532
40 025 61 152 82 331 103 546
41 026 62 155 83 343 104 565
42 031 63 156 84 346 105 606
43 032 64 162 85 351 106 612
44 043 65 165 86 364 107 624
45 047 66 172 87 365 108 627
46 051 67 174 88 371 109 631
47 054 68 205 89 411 110 632
48 065 69 223 90 412 111 654
49 071 70 226 91 413 112 662
50 072 71 243 92 423 113 664
51 073 72 244 93 431 114 703
52 074 73 245 94 432 115 712
53 114 74 251 95 445 116 723
54 115 75 261 96 464 117 731
55 116 76 263 97 465 118 732
56 125 77 265 98 466 119 734
57 131 78 271 99 503 120 743
58 132 79 306 100 506 121 754
59 134 80 311 101 516
Setting andTransmitting Call Tones
Your radio can transmit different call tones to other radios in your group
so you can alert them that you want to talk. You have 10 call tones from
which to choose.
To set a call tone:
1. With the radio on, short press until the current call tone setting
flashes and J appears.
2. Press O or O to change and hear the call tone.
3. Press (m) to set the new call tone or to continue set up.
To transmit your call tone to other radios set to the same channel and
Interference Eliminator Code as your radio, press J" .
Note: Setting the call to 0 disables the call tone feature.
Hands-Free Use Without Accessories (iVOX)
You can use the iVOX feature to transmit, hands-free without the need
for any voice activation accessories. Once iVOX is turned on, the radio
detects your voice and transmits when you speak.
1. Short press until iVOX appears on the display. The current
setting On/Off will flash.
2. Press O or O to select On or Off.
3. Press(Qto set or to continue set up.
4. To transmit, speak into the radio microphone. There is a short delay
between the time you start talking and when the radio transmits.
5. To receive, stop talking.
Setting the Sensitivity Level When in VOX or iVOX Mode
Adjusting the radio's sensitivity level helps minimize the possibility of
unintended noises triggering a transmission and helps the radio pick up
soft voices.
1. Short press (^^until icon VOX or iVOX appears and the level
number blinks.
2. Press O or O to select the sensitivity level.
3. Press @ to set or (^^to continue set up.
3 = High Sensitivity for quiet environments
2 = Medium Sensitivity for most environments
1 = Low Sensitivity for noisy environments
Note: When you connect a VOX accessory or enable iVOX, the radio is
automatically set to the respective last chosen sensitivity level.
See Special Features section on Accessories.
VibraCall™ Alert
VibraCall is a vibrating alert that notifies you that your radio is receiving
a message. This is useful in noisy environments. When the alert is on,
the radio vibrates once every 30 seconds when you receive a message
on the channel and code you set.
1. To turn vibrating alerts on, press (^^until is displayed. The
current setting will flash.
2. Press O or O to change the setting to Off/On.
3. Press Q to set or ^^to continue set up.
QT Noise Filtering
The QT noise-filtering feature helps to ensure uninterrupted
communication with other Motorola radios that have this feature. This
feature filters out unwanted transmissions from other radios. This is
useful in places where there is heavy radio traffic, such as amusement
parks or ski resorts.
Note: QT noise filtering is not available when the radio is scanning.
To turn QT noise filtering on or off:
1. Short press until QT displays. The current setting On/Off will
flash.
2. Press O or O to turn noise filtering On or Off.
3. PressQto confirm your selection or ^^to continue set up.
To transmit to a radio that has QT noise filtering turned on:
1. Selectthe same channel and Interference Eliminator Code as the
other radio.
2. Press J to send a call tone. This allows yourvoice to pass through
the QT noise filter on the receiving radio.
3. Press © and speak normally.
Note: If you skip step 2, the beginning of your message may not be
heard on the receiving radio. For a 30-second period, starting after the
last transmission, all transmissions received on the selected channel
and code will pass through the QT noise filter.
Keypad Tones
You may enable or disable the speaker key tones. You will hear the key
tone each time a button is pushed.
1. Press (^^until J" appears. The current setting On/Off will flash
2. Press either O or O to turn On or Off.
3. Press Q to confirm or (^^to continue set up.
When the Key Tone Feature is off, the following are not disabled:
• Transmit timeout alert tone;
• Power-down alert tone;
• Low battery alert tone; or
• The transmitted Talk Confirmation Tone.
Transmitting aTalk Confirmation Tone
You can setyour radio to transmit a unique tone when you finish
transmitting. It is like saying "Roger" or "Over" to let others knowyou
are finished talking.
1. With the radio on, press until the appears. The current
setting On/Off flashes.
2. Press or O to turn On or Off.
3. Press Q to set or(J^to continue set up.
Special Features
Keypad Lock
To avoid accidentally changing your radio settings:
1. Press and hold until ^displays.
2. When in lock mode, you can turn the radio on and off, adjust the
volume, receive, transmit, send a call tone, and monitor channels. All
other functions are locked.
To unlock the radio, press and hold until is no longer displayed.
Priority Scan
Use scan to monitor channels and codes for transmissions or to find
someone in your group who has accidentally changed channels.
With priority scan,your home channel is scanned more frequently than
any other channel. The home channel is the channel where your radio
was set when you started to scan. If you activate scan while your
radio's Interference Eliminator Code is set to a number between 1 and
121, the radio checks for activity on each programmed channel and
code combination.
Notes:
• All transmissions using code 0 or any other code are ignored.
• The default code for each channel is 1.
• If scanning on code 0, all channels and code combinations are
scanned.
1. To start scanning, briefly press and release The scan indicator
displays and the radio begins to scroll through the channel but
the 0 (if scanning on code 0) o r ( t w o hyphens, if scanning on non
zero code) won't scroll.
2. When the radio detects channel activity, it stops scanning and you
can hear the transmission.
3. To respond and talk to the person transmitting, press(Q within five
seconds.
4. To stop scanning, briefly press and release .
Note: If you press@ while the radio is scanning, the radio will
transmit on the channel you selected before you activated scan or the
channel which the radio stops at and is listening to. If no transmission
occurs within five seconds, scanning will resume.
Removing Channels from the Scan List (Nuisance Delete
Feature)
1. To preventthe radiofrom scanning a channel,press and hold O or
for at least three seconds, then release, when the scan first
stops on that channel. This temporarily removes the channel from
the scan list.
2. Press to exit scan mode.
3. Press^^a second time to activate scan again.
4. To restore a previously deleted channel, turn the radio off and then
back on or just repeat step 2 and step 3.
Note: You cannot remove your home channel from the scan list. The
home channel is the channel your radio was set to when you started
the scanning.
Using Audio Accessories:
Many accessories (sold separately) are available for your radio. For
more information, visit our Web site atwww.motorola.com.
Hands-Free Use With Accessories (VOX)
You can transmit hands-free with the use of optional accessories. Once
VOX is turned on, the radio detects your voice and transmits when you
speak.
1. Turn the radio off and plug the VOX accessory into the accessory
port.
2. Turn the radio on. VOX shows on the display.
3. Adjust the volume appropriately by rotating Q . Lower the volume
before placing the accessory on your head or in your ear.
4. To transmit, speak into the accessory microphone.
5. To receive, stop talking.
6. To turn off, simply remove the accessory.
Note: There is a short delay between the time you start talking and
when the radio transmits. There is a short delay before the
transmission is completed.
Patent and Copyright Information
Manufactured, distributed and sold by Giant International Ltd., official
licensee for this product. Motorola, the Motorola logo trademarks and
the Motorola trade dress are owned by Motorola, Inc. and are used
underlicense from Motorola, Inc. Oricom International is the local
distributor of Motorola 2-way UFIF radios in Australia & New Zealand.
Please contact customer service hotline at 1300 889 785 (Australia) or
0900 50 025 (Toll Call, New Zealand) for questions/comments,warranty,
support, or service related to this product. MOTOROLA and the Stylized
M Logo are registered in the U.S. Patent & Trademark Office. All other
product or service names are the property of their respective owners. ©
Motorola, Inc. 2006. All rights reserved.
Warranty
Limited Warranty for Personal Communication Products,
Accessories and Software Purchased in Australia or New
Zealand.
What Does this Warranty Cover?
This limited warranty is a consumer's exclusive remedy, and applies as
follows to new Motorola branded Products, Accessories and Software
manufactured, distributed and sold by Giant International Ltd., Oricom is
the local distributor in Australia & New Zealand, which warrants
Motorola 2-way UFIF Radio Products and Accessories (collectively
"Equipment') purchased against defects in material and workmanship
under normal use and service for the following period of time:
This express warranty is given in addition to any rights or remedies that
may be available to the Customer under the Consumer Guarantees Act
1993 ("CGA"), and does not limit any rights and remedies available to the
Customer under the CGA.
If the customer is a consumer (as that term is defined in the CGA) then:
A. This Warranty shall apply for the benefit of the Customer, and any
Consumer acquiring from or through the Customer: and
B. Any of the provisions of this warranty which reduce, limit or are
contrary to the guarantees and remedies contained in the CGA, shall be
deemed deleted and omitted from this Warranty UNLESS the Customer is
a Consumer who acquires the products for the purposes of a business,
and the supplier of the products to the Customer has contracted out of
the provisions of the CGA.
Products Covered
Products and Accessories as
defined above, unless otherwise
provided for below.
1. Decorative Accessories and
Cases. Decorative covers,
bezels, PhoneWrap covers and
cases.
2. Consumer Two-Way Radio
Accessories.
3. Products and Accessories that
are Repaired or Replaced.
Length of Coverage
One (1) year from the date of
purchase by the first consumer
purchaser of the product unless
otherwise provided for below.
1. Limited lifetime warranty for
the lifetime of ownership by the
first consumer purchaser of the
product.
2. Thirty (30) days from the date of
purchase by the first consumer
purchaser of the product.
3. The balance of the original
warranty or for thirty (30) days
from the date returned to the
consumer, whichever is longer.
Notes: You are required to provide proof of purchase as a condition of
receiving warranty services. You are entitled to a replacement or repair
according to the terms and conditions of this document if your product
is found to be faulty within the Warranty Period. This Warranty extends
to the original purchaser only and is not transferable.
Who is covered?
This warranty extends only to the first consumer purchaser, and is not
transferable.
What will the distributor do?
Distributor, at its option, will at no charge repair, replace any products
and Accessories that does not conform to this warranty. We may use
functionally equivalent reconditioned/refurbished/pre-owned or new
Products and Accessories or parts. No data, software or applications
added to your Product, Accessory, including but not limited to personal
contacts, games and ringer tones, will be reinstalled. To avoid losing
such data and applications please create a back up prior to requesting
service.
How to Obtain Warranty Service or other Information?
To obtain service or information, please call:
Oricom International Pty Ltd
Australia call
- 1300 889 785
(cost of local call excludes calls from
mobiles)
Oricom International Pty Ltd
New Zealand call
0900 50 025
(Toll Call)
For Accessories, please call the telephone number designated above
for the product with which they are used.
You will receive instructions on how to ship the Products or
Accessories, atyour expense, to an authorised repair Center. To obtain
service, you must include: (a) a copy of your receipt, bill of sale or other
comparable proof of purchase; (b) a written description of the problem;
(c) the name and location of the installation facility (if applicable) and,
most importantly; (e) your address and telephone number.
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are excluded from
coverage.Batteries. Only batteries whose fully charged capacity falls
below 80% of their rated capacity and batteries that leak are covered
by this limited warranty.
Abuse & Misuse. Defects or damage that result from: (a) improper
operation, storage, misuse or abuse, accident or neglect, such as
physical damage (cracks, scratches, etc.) to the surface of the product
resulting from misuse; (b) contactwith liquid, water, rain, extreme
humidity or heavy perspiration, sand, dirt or the like, extreme heat, or
food; (c) use of the Products or Accessories for commercial purposes
or subjecting the Product or Accessory to abnormal usage or
conditions; or (d) other acts which are not the fault of Motorola or Giant
International Ltd., are excluded from coverage.
Use of Non-Motorola branded Products and Accessories.
Defects or damage that result from the use of Non-Motorola branded or
certified Products, Accessories, Software or other peripheral
equipment are excluded from coverage.
Unauthorized Service or Modification. Defects or damages
resulting from service, testing, adjustment, installation, maintenance,
alteration, or modification in any way by someone other than Motorola,
Giant International Ltd. or its authorized service centers, are excluded
from coverage.
Altered Products. Products or Accessories with (a) serial numbers
or date tags that have been removed, altered or obliterated; (b) broken
seals or that show evidence of tampering; (c) mismatched board serial
numbers; or (d) nonconforming or non-Motorola branded housings, or
parts, are excluded from coverage.
Communication Services. Defects, damages, or the failure of
Products, Accessories or Software due to any communication service
or signal you may subscribe to or use with the Products Accessories or
Software is excluded from coverage.
This Warranty in no way affects your statutory warranty rights under
the Trade Practices Act 1974 or any other similar legislation. This
Warranty does not extend to any product from which the serial number
has been removed,was purchased outside of Australia orthathas
been damaged or rendered defective:
1. as a result of lightning, over voltage, accident, misuse, abuse or other
external causes;
2. the operation outside the normal use of the product;
3. by the use of parts not manufactured or
4. Only batteries whose fully charged capacity falls below 80% of their
rated capacity and batteries that leak are covered by this warranty.
Nothing in this Warranty excludes, restricts or modifies any condition,
warranty, right or remedy which pursuant to the Trade Practices Act
1974 applies to this Warranty and which may not be so excluded,
restricted or modified. For warranties that cannot be excluded,
restricted or modified, Oricom limits the remedies available to those
specified in the relevant legislation.
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED TO THE DURATION OF THIS
LIMITED WARRANTY, OTHERWISE THE REPAIR, REPLACEMENT, OR
REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS
THE EXCLUSIVE REMEDY OF THE CONSUMER, AND IS PROVIDED IN
LIEU OFALL OTHER WARRANTIES, EXPRESS OF IMPLIED. IN NO
EVENT SHALL MOTOROLA OR GIANT INTERNATIONAL LTD. BE LIABLE,
WHETHER IN CONTRACT OR TORT (INCLUDING NEGLIGENCE) FOR
DAMAGES IN EXCESS OFTHE PURCHASE PRICE OFTHE
PRODUCT, ACCESSORY OR SOFTWARE, OR FOR ANY INDIRECT,
INCIDENTAUSPECIALOR CONSEQUENTIAL DAMAGES OF ANY KIND,
OR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS,
LOSS OF INFORMATION OR DATA, SOFTWARE OR APPLICATIONS OR
OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH
THE ABILITY OR INABILITY TO USE THE PRODUCTS, ACCESSORIES OR
SOFTWARE TO THE FULL EXTENT THESE DAMAGES MAY BE
DISCLAIMED BYLAW.
Some states and jurisdictions do not allow the limitation or
exclusion of incidental or consequential damages, or
limitation on the length of an implied warranty, so the above
limitations or exclusions may not apply to you.This warranty
gives you specific legal rights, and you may also have other
rights that vary from state to state or from one jurisdiction to
another.
Laws in the United States and other countries preserve for Motorola
certain exclusive rights for copyrighted Motorola software such as the
exclusive rights to reproduce and distribute copies of the Motorola
software. Motorola software may only be copied into, used in, and
redistributed with, the Products associated with such Motorola software.
No other use, including without limitation disassembly of such Motorola
software or exercise of the exclusive rights reserved for Motorola, is
permitted.
SX709