VintageView E18-X - 8 Evolution Extension Package - Manual (Page 2)

4. Affix the Second Panel – Carefully lift and rotate the partially
assembled unit to rest on the panel with the unsecured ends
upright, like a bed of nails. Lay the second panel on the ends of the
E1’s and one at a time, align each E1 with the corresponding hole
and secure it in place with an E1-SCREW (Fig. A.). If assembling
a multi-section unit, use the E1-STUD instead (Fig. B.). It is
recommended that the E1’s be secured row-by-row working down
the panel, as this will allow the easiest alignment of the E1 with
the holes. For single section units, the assembly is complete, skip
to Step 6.
Tip: The E1-STUD’s may be quickly screwed in by gently tightening
them in the chuck of a drill with approximately 3/4 of the stud
exposed, screwing them in until the flat spot in the middle of the
stud is just below the surface of the panel and then releasing the
end of the stud from the chuck.
Lifetime Warranty
Wine Master Cellars, LLLP (WMC) warrants to the original consumer-purchaser that
this product shall be free from defects in workmanship and materials under normal
and reasonable use for the lifetime of the product. WMC will, at its option, refinish or
replace any product or part found to be defective during the warranty period and excludes
installation charges, shipping costs, and the cost of removal and reinstallation. WMC may
require you to return the part(s) claimed to be defective, for its inspection - freight or
postage prepaid.
This warranty does not include the cost of any inconvenience or property damage
due to the failure of the product and does not cover damage due to Devine Act, third
party act out of the control of WMC, misuse, abuse, accident, or damage arising out of
transportation of this product. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL
OTHER OBLIGATIONS, LIABILITIES OR WARRANTIES AND THERE IS NO WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
In no event shall WMC be liable or responsible for INCIDENTAL OR CONSEQUENTIAL
DAMAGES or for any other direct or indirect damage, loss, cost, expense, or fee. Neither
the WMC distributor nor the retail establishment selling this product has any authority
to make any warranties or to promise remedies in addition to or inconsistent with those
stated above. WMC’s maximum liability, in any event, shall not exceed the purchase price
of the product paid by the original consumer-purchaser.
All matters regarding the sale of the product or this warranty shall be governed by the
laws of the state of Colorado and the exclusive jurisdiction of and venue for any warranty
claims or claims directly or indirectly related to the sale of the product shall be Colorado.
Any claim, or action relating the purchase of the product or this warranty must be filed
no more than six (6) months after the date the claim arose. All statute of limitations to
the contrary are waived.
Some states do not allow the exclusion or limitation of incidental or consequential
damages. In such case, the above limitations or exclusions may not be applicable. This
warranty gives you specific legal rights and you may also have other rights which vary
from state to state.
Please call us toll free at 866-650-1500 for assembly assistance or to request replacement parts.
www.VintageView.com
5. Attach the E1’s to Exposed Studs (for Extensions only) –
With all of the studs installed, begin securing the panel in place
by installing E1’s along the top, middle and bottom rows. Once
the second panel is firmly locked in place, the unit may be stood
upright for ease of access while installing the remaining E1’s.
Tip: The E1’s may be quickly installed by gently tightening one end
of the tube in the chuck of a drill and screwing the other end onto
the exposed E1-STUD. Remember to keep the drill set at a low
torque so as not to overtighten or damage anything.
6. Secure to Wall – It is highly recommended that all units be
secured to a wall for optimal stability. This may be accomplished
by either directly fastening a panel to the wall by pre-drilling a
hole through the panel and screwing or bolting into the wall or by
using an “L” bracket. Please contact your VintageView dealer for
information regarding brackets of custom shapes or sizes.
Fig. A Fig. B