Tycon Power SLC-2405B/08B/10B/15B - Manual

2 3 4
Dear User:
automatic identification. Please read this manual carefully before use to
ensure correct, safe and effective product operations. Please keep this
manual in a safe place for future reference.
Product Introduction
multi-functional solar chargers. These devices incorporate PWM
technology to control the solar charging. Effectively keeping all system
components safe, extending the working life of the battery and
maintaining system efficiency.
alone systems including solar fences, lighting, gate openers, security
cameras, etc.
Main Functional Characteristics
automatically.
PWM technology protects system overcharge and overflow.
Controlled charging maintains excellent battery condition and
extended working life.
Reverse polarity protection.
Open circuit protection, prevents battery discharge and solar module
damage at night.
Lightning protection.
Three LED display clearly indicates the working status of the system.
(protected) use only.
It should be installed in a
shaded location, avoiding
direct sunlight and must be
free from moisture.
If the controller is to be used
outside, please place the
controller in a protective
housing keeping it free from
dust and water.
Our Temperature Compensation Sensor Option allows the
controller to detect the surrounding temperature, automatically
adjusting the charging voltage. The controller and battery
should be placed in the same room.
The surface temperature of
the controller will heat up
during use, please avoid
contact and exposure with
combustibles.
Mounting & Installation
4 screws are provided for mounting
purposes.
Please ensure both cooling vents
on either side of the controller are
free from obstruction to ensure
sufficient air flow.
Connection Sequence
*Warning:The following connection sequence must be followed at all
times to avoid possible damage and personal injury!
Solar Panel
30~100cm
Battery
Load
1 Battery Connection
The battery must be connected first
using the clearly marked connections
on the controller.
Note the recommended distance
between the battery and the controller
should be between 30cm and 100cm.
The controller has reverse polarity
connection, just change the polarity
if the battery is incorrectly connected.
2 Solar Module Connection
Connect the wires to the
controller first, then connect
the panel. 3 Load (Device) Connection
Connect load (Device) first and
then controller to avoid any
damage and/or malfunctions.
Load
Solar Panel
Battery
4 Complete Wire Connection Diagram
Recommended System
Wire Sizes(including wires
between the controller and
panel, battery, load):
LED Display Function
Amber LED
Red LED
Green LED
LED Explanation
Amber LED:
On (Solid):The controller is connected correctly/Battery fully charged.
On (Flashing):Controller is charging.
Red LED:
On (Solid):The battery is fully charged.
Green LED:
On (Solid):Load output is OK.
Off:Battery voltage is low.
LED Sequence
Phase 1 - Amber LED Flashing, no other LEDS are lit
Battery is being charged and voltage is below 12.4V for 12V systems
and 24.8V for 24V systems.
Note: When the voltage is under 11.1V (12V system) or 22.2V (24V
system), the battery will stop powering the load.
Phase 2 - Amber LED is flashing and the Green LED is lit
Battery has reached 12.4V or 24.8V and the controller continues to
charge.
Phase 3 - Amber LED is flashing, Green LED is lit
Battery has reached maximum charge around 14.4V or 28.8Vand the
controller remains charging with a very small trickle charge.
Phase 4 - Yellow LED, Red LED and Green LED are all lit (No flashing)
Battery has reached 13.8V, no charging is taking place.
Phase 5 - Yellow LED starts flashing, Red LED turns off and Green LED
stays on
Battery has reached 13.2V, and the controller has started charging again.
If voltage drops below 12.4V due to load the Green LED will turn off.
Warning - Important Safety Instructions when
connecting the panel.
Put the positive and negative of the wire close to reduce
the electromagnetic interference.
Do not connect the solar module while it is exposed to
daylight. This may generate voltage instantly, causing
system damage and/or personal injury.
Ensure the solar module is rated at the correct voltage
to charge the battery you are connecting, failure to do
so may cause permanent harm to the battery.
Controller. The TP-SC24-10 has 12/24VOLT
Thank you for choosing the TYCON TP-SC-24-10 Smart Solar Charge
The Tycon TP-SC24-10 controller family is our new generation of
The Tycon TP-SC24-10 controller is designed for small, remote stand
Intelligent controller (SC-24-10) identifies system voltage 12V/24V
The Installation and Connection of the SC24-10 Solar Controller
The SC24-10 controller is
designed for indoor
S C24-10: at least 6.0 mm²