Wiring duct booster – Tjernlund DB-2 Duct Booster 8504030 Rev B 09/00 User Manual
Page 2
INSTALLATION (Tools Required)
DRILL
1/4” NUT RUNNER
5/16” DRILL BIT
1/4” WRENCH
SCREW DRIVER
TIN SNIPS
NOTE: If installing the DUCT BOOSTER® on a flat duct, the housing
flanges will have to be bent at a 90
O
angle before inserting DUCT
BOOSTER® into duct. This will allow screws to better align with the
speed clips provided.
1. Opening should be cut in the bottom or top of a horizontal duct or any side of
a vertical duct. The motor shaft will then be in the horizontal position. Apply
the mounting template provided to the duct, cut opening and drill four 5/16”
holes noted on template.
WIRING DUCT BOOSTER
®
IN PARALLEL WITH HEAT CYCLE
OR COOLING/BLOWER “ON” CYCLE
See also other documents in the category Tjernlund Equipment:
- 950-0014 Relay Timer Airotronics Non-Adjustable 8504067 Rev. A 11/11 (2 pages)
- 950-0014 Relay-Timer (Old Style) Kit Non-Adjustable 8504067 Rev. 10/97 (2 pages)
- 950-0015 SS2 Motor Kit 8504069 Rev. 05/98 (2 pages)
- 950-0017 SS2 Impeller Kit 8504070 Rev. 03/98 (1 page)
- 950-0019 SS2 Venter Housing Kit 8504072 Rev. 05/98 (1 page)
- 950-4020 I, IL, XL Motor Kit 8504051 Rev 2 11/96 (2 pages)
- 950-0452 PAI-1,2 Prover Kit 8504044 Rev. 1 04/97 (2 pages)
- 950-0453 PAI-T Timer-Clock Kit 8504045 Rev. 1 05/97 (2 pages)
- 950-0476 Commercial PAI Series Fan Prover Kit 8504086 Rev. A 01/00 (1 page)
- 950-0484 Mac-3 (Discontinued - No longer available) Board Kit 8505009 Rev. 08/00 (9 pages)
- 950-0625 SS1 Motor Kit 8504016 Rev. A 11/99 (2 pages)
- 950-0640 SS1 Series High Limit Kit 8504042 Rev. 2 03/98 (1 page)
- 950-0740 SS1C Series High Limit Kit 8504042 Rev. 2 03/98 (1 page)
- 950-0750 SS1C Fan Prover Kit 8504037 Rev. 09/94 (1 page)
- 950-1007 Fan Prover Kit 8504113 (1 page)
- 950-1020 Motor Kit 8504048 Rev 2 12/97 (2 pages)
- 950-1021 Motor Kit 8504049 Rev 2 11/96 (2 pages)
- 950-1022 Motor Kit 8504050 Rev. 1 11/96 (2 pages)
- 950-1040 24V Relay Kit 8504052 Rev. 3 10/97 (2 pages)
- 950-1067 Relay-Timer Airotronics - Adjustable 8504053 Rev. A 04/12 (4 pages)
- 950-1067 Relay-Timer (Old Style) Kit 8504053 Rev 4 09/96 (4 pages)
- 950-2043 ND-1 Post Purge Burner Kit 8504004 Rev 0196 (4 pages)
- 950-2061 Pilot Saver Kit 8504028 Rev 2 09/95 (2 pages)
- 950-2064 L-185 Safety Interlock Kit 8504020 Rev 3 09/96 (2 pages)
- 950-2080 New Style Gas Pressure Switch (1 page)
- 950-2420 24SP200 Spillage Kit 8504056 Rev 1 03/97 (2 pages)
- 950-3022 Motor Kit 8504066 Rev 1 05/98 (3 pages)
- 950-4030 AD-1 Speed Controller Kit 8504005 Rev 03/96 (1 page)
- 950-8804 UC1 Universal Control Board Kit (Version X.06) 8505017 Rev D 07/05 (17 pages)
- 950-8804 UC1 Universal Control Board Kit (Version X.04) 8505017 Rev A 05/03 (16 pages)
- SB1 Heat Shield Kit 8504184 (2 pages)
- DJ-3, D-3, HD, I, IL, XL Draft Inducer 8504003 Rev A 07/00 (12 pages)
- PS1505 Fan Prover 8504008 Rev 1 01/97 (2 pages)
- AD-1 for Wood or Coal Stoves 8504012 Rev A 10/99 (2 pages)
- CSA1 Chimney Stack Assist Kit 8504201 (8 pages)
- RTS8 Rooftop Mounting Kits 8504161 (1 page)
- COP2 Constant Operating Pressure Exhaust Control 8504208 (11 pages)
- CIC1 Heater Interlock Control for COP2 8504209 (2 pages)
- DCOP1 Constant Operating Pressure Draft Control 8504174 (Discontinued) (20 pages)
- XCOP1 Constant Operating Pressure Exhaust Control 8504175 (Discontinued) (7 pages)
- UCRT Rooftop Inducer Universal Control (Version X.06) 8504162 Rev A 05/11 (16 pages)
- UCRT Rooftop Inducer Universal Control (Version X.06) 8504162 Rev 01/10 (16 pages)
- MAC1E Control Version F (Compatible with UC1 Control) 8504110 Rev B 11/05 (2 pages)
- MAC1E Control (Compatible with UC1 Control) 8504110 Rev A 12/04 (2 pages)
- MAC4E Control Version F (Compatible with UC1 Control) 8504112 Rev B 08/05 (2 pages)