Kontron AM4150 User Manual
User guide, Am4150
Table of contents
Document Outline
- Revision History
- Imprint
- Disclaimer
- Table of Contents
- List of Tables
- 1-1 System Relevant Information 1 - 5
- 1-2 AM4150 Main Specifications 1 - 9
- 1-3 Standards 1 - 13
- 1-4 Related Publications 1 - 14
- 2-1 Features of the Processors Supported on the AM4150 2 - 3
- 2-2 Module Management LEDs Functions 2 - 7
- 2-3 User-Specific LEDs Functions 2 - 8
- 2-4 User-Specific Debug Code Sequence 2 - 9
- 2-5 User-Specific Debug Code Example 2 - 9
- 2-6 Module Handle Positions 2 - 10
- 2-7 COP Debug Connector J8 Pinout 2 - 11
- 2-8 Serial Con. J4 (UART1) Pinout 2 - 12
- 2-9 Gigabit Ethernet Port Assignment 2 - 13
- 2-10 GbE Connectors J2 / J3 Pinout 2 - 14
- 2-11 CPU SerDes Interface Configuration 2 - 17
- 2-12 AMC Ports 4 - 7 SerDes Bank/Lane/Signal Assignment 2 - 18
- 2-13 AMC Ports 8 - 11 SerDes Bank/Lane/Signal Assignment 2 - 18
- 2-14 Pinout of AMC Card-edge Connector J1 2 - 20
- 2-15 Reserved Pins Description 2 - 24
- 2-16 Extended Options Region Single-Ended Pins Description 2 - 25
- 2-17 JTAG Pins Description 2 - 25
- 2-18 Processor and Chipset Supervision 2 - 27
- 2-19 AMC-Specific Signals 2 - 27
- 2-20 Onboard Power Supply Supervision 2 - 27
- 2-21 Temperature Signals 2 - 27
- 4-1 DIP Switch SW2 Configuration 4 - 3
- 4-2 Fail-Safe AMC Fabric Configuration 4 - 4
- 4-3 AM4150 Virtual and Physical Memory Address Map 4 - 5
- 4-4 I/O Address Map 4 - 6
- 4-5 Status Register 0 (STAT0) 4 - 7
- 4-6 Device Protection Register (DPROT) 4 - 8
- 4-7 Reset Status Register (RSTAT) 4 - 9
- 4-8 Board Interrupt Configuration Register (BICFG) 4 - 10
- 4-9 Board ID High Byte Register (BIDH) 4 - 10
- 4-10 Board and PLD Revision Register (BREV) 4 - 11
- 4-11 Geographic Addressing Register (GEOAD) 4 - 11
- 4-12 Watchdog Timer Control Register (WTIM) 4 - 13
- 4-13 Board ID Low Byte Register (BIDL) 4 - 14
- 4-14 LED Configuration Register (LCFG) 4 - 15
- 4-15 LED Control Register (LCTRL) 4 - 16
- 5-1 DC Operational Input Voltage Ranges 5 - 3
- 5-2 AM4150 in U-Boot Shell Mode 5 - 5
- 5-3 AM4150 with Linux in Idle Mode 5 - 5
- 5-4 AM4150 with Linux and Maximum Processor Work Load (“stress” tool) 5 - 5
- 5-5 Payload Power Consumption of AM4150 Accessories 5 - 5
- 5-6 IPMI FRU Payload Power Consumption 5 - 6
- 6-1 AM4150 Airflow Impedance by Zone [N/m²] 6 - 7
- 6-2 AM4150 Airflow Impedance by Zone [inches H2O] 6 - 8
- 6-3 AM4150 Deviation of the Airflow Rate [%] 6 - 9
- A-1 SATA Flash Module Main Specifications A - 3
- List of Figures
- 1-1 AM4150 Functional Block Diagram 1 - 6
- 1-2 AM4150 Front Panel 1 - 7
- 1-3 AM4150 Board Layout (Top View) 1 - 8
- 1-4 AM4150 Board Layout (Bottom View) 1 - 8
- 2-1 Front Panel LEDs 2 - 6
- 2-2 Module Handle Positions 2 - 10
- 2-3 COP Debug Connector J8 2 - 11
- 2-4 Serial Con. J4 (UART1) 2 - 12
- 2-5 GbE Con. J2/J3 2 - 14
- 2-6 AM4150 Port Mapping 2 - 15
- 3-1 Module Handle Positions 3 - 4
- 3-2 J9 microSDHC Memory Card Socket 3 - 8
- 3-3 Placement of the SATA Flash Module 3 - 9
- 4-1 DIP Switch SW2 4 - 3
- 6-1 Operating Limits of the AM4150 with QorIQ™ P5020, 2.0 GHz 6 - 5
- 6-2 Operating Limits of the AM4150 with QorIQ™ P5020, 1.8 GHz 6 - 5
- 6-3 Operating Limits of the AM4150 with QorIQ™ P5020, 1.6 GHz 6 - 6
- 6-4 AM4150 Airflow Impedance 6 - 7
- 6-5 Thermal Zones of the AM4150 Module 6 - 8
- A-1 SATA Flash Module Layout (Bottom View) A - 4
- Proprietary Note
- Trademarks
- Environmental Protection Statement
- Explanation of Symbols
- For Your Safety
- Two Year Warranty
- 1. Introduction