Craftsman 917.275900 - Manual (Page 8)

TO DRIVE TRACTOR OFF SKID
(See Operation section for location
Md function of controls)
WARNING: Before starting, read, un­
derstand and follow all instructions in the
Operation section of this manual. Be sure
tractor is in a well-ventilated area. Be sure
the area in front of tractor is clear of other
people and objects.
1. Be sure all the above assembly steps
have been completed.
2. Check engine oil level and fill fuel tank
with gasoline.
3. Place freewheel control in "trans­
mission engaged" position (see "TO
TRANSPORT" in Operation section of
this manual).
4. Sit on seat in operating position,
depress clutch/brake pedal and set the
parking brake.
5. Place motion control lever in neutral
(N) position.
6. Press lift lever plunger and raise attach­
ment lift lever to its highest position.
7. Start the engine. After engine has started,
move throttle control to idle position.
8. Release parking brake.
9. Slowly move the motion control lever
forward and slowly drive tractor off skid.
10. Apply brake to stop tractor, set parking
brake and place motion control lever in
neutral position.
11 .Turn ignition key to "STOP" position.
Continue with the instructions that follow.
CHECK TIRE PRESSURE
The tires on your tractor were over inflated
at the factory for shipping purposes. Cor­
rect tire pressure is important for best
cutting performance.
• Reduce tire pressure to PSl shown in
"PRODUCT SPECIFICATIONS” section
of this manual.
CHECK DECK LEVELNESS
For best cutting results, mower hous­
ing should be properly leveled. See “TO
LEVEL MOWER HOUSING” in the Service
and Adjustments section of this manual.
CHECK FOR PROPER POSITION
OF ALL BELTS
See the figures that are shown for replac­
ing motion and mower blade drive belts
in the Service and Adjustments section
of this manual. Verify that the belts are
routed correctly.
8
CHECK BRAKE SYSTEM
After you learn how to operate your trac­
tor, check to see that the brake is properly
adjusted. See “TO ADJUST BRAKE” in
the Service and Adjustments section of
this manual.
/CHECKLIST
Before you operate your new tractor, we
wish to assure that you receive the best
performance and satisfaction from this
Quality Product.
Please review the following checklist:
/ All assembly instructions have been
completed.
/ No remaining loose parts in carton.
/ Battery is properly prepared and
charged. (Minimum 1 hour at 6 amps).
/ Seat is adjusted comfortably and tight­
ened securely.
/ All tires are properly inflated. (For ship­
ping purposes, the tires were overin­
flated at the factory).
/ Be sure mower deck is properly leveled
side-to-side/front-to-rear for best cutting
results. (Tires must be properly inflated
for leveling).
/ Check mower and drive belts. Be sure
they are routed properly around pulleys
and inside all belt keepers.
/ Check wiring. See that all connections
are still secure and wires are properly
clamped.
/ Before driving tractor, be sure freewheel
control is in “transmission engaged”
position (see “TO TRANSPORT” in the
Operation section of this manual).
While learning how to use your tractor, pay
extra attention to the following important
items:
/ Engine oil is at proper level.
/ Fuel tank is filled with fresh, clean, regu­
lar unleaded gasoline.
/ Become familiar with all controls, their
location and function. Operate them
before you start the engine.
/ Be sure brake system is in safe operat­
ing condition.
/ Be sure Operator Presence System and
Reverse Operation System (ROS) are
working properly (See the Operation and
Maintenance sections in this manual).
/ It is important to purge the transmission
before operating your tractor for the first
time. Follow proper starting and trans­
mission purging instructions (See “TO
START ENGINE” and “PURGE TRANS­
MISSION” in the Operation section of
this manual).