LG RU-42PZ61/71 - Manual (Page 37)

External Control Device Setup
Set ID
- Use this function to specify a monitor ID number.
- Refer to ‘Real Data Mapping
V . See page 37.
1. Press the MENU button and then use
d / E button to select the SPECIAL menu.
2. Press the
g
button and then use
d
/ E button to select Set ID.
3. Press the
g
button and then use
f
/
g
button to adjust Set ID to choose the
desired monitor ID number. The adjustment range of Set ID is 1 ~ 99.
4. Press the ENTER button to save.
oi
Communication Parameters
Baud rate :9600 bps (UART)
Data length : 8 bits
Parity : None
Use a crossed (reverse) cable.
Command Reference List
Stop bit: 1 bit
Communication code : ASCII code
Transmission / Receiving Protocol
Transmission
DATA
(Hexadecimal)
01. Power k a 0~ 1
02. Input Select k b 0~6
03. Aspect Ratio k C 0~3
04. Screen Mute k d 0~ 1
05. Volume Mute k e 0~ 1
06. Volume Control k f 0~64
07. Contrast k g 0~64
08. Brightness k h 0~64
09. Color k i 0~64
10. Tint k i 0~64
11. Sharpness k k 0~64
12. OSD Select k 1 0~ 1
13. Remote Control Lock Mode k m 0~ 1
14. PIP/DW k n 0~3
15. Split Zoom k p 0~99
16. PIP Position k q 0~3
17. Treble k r 0~64
18. Bass k S 0~64
19. Balance k t 0~64
20. Color Temperature k u 0~3
21. Red Adjustment k V 0~3C
22. Green Adjustment k w 0~3C
23. Blue Adjustment k $ 0~3C
24. PIP Input Source k y 0~6
25. Abnormal State k Z 0~a
26. ISM Method
i p 0~3
27. Low Power
i
q 0~ 1
28. Orbiter Time Setting j r 1 ~FE
29. Orbiter Pixel Setting j S 1~9
30. Picture Size j t 0~14
31. Auto Config j u 1
[Command 1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1]: First command to control PDP set. (j, k or m)
* [Command 2]: Second command to control PDP set.
* [Set ID]: You can adjust the set ID to choose desired monitor
ID number in Special menu. Adjustment range is 1
~ 99. When selecting Set ID ‘O’, every connected
PDP set is controlled. Set ID is indicated as deci­
mal (1~99) on menu and as Hexa decimal
(0x0~0x63) on transmission/receiving protocol.
* [DATA]: To transmit command data.
Transmit ‘FF’ data to read status of command.
* [Cr]: Carriage Return
ASCII code ‘OxOD’
* [ ]: ASCII code ‘space (0x20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving abnormal data from non-viable
functions or communication errors.
Data 1: lilegal Code
2: Not supported function
3: Wait more time
COM- COM- DATAO DATAI DATA 2 DATA3
MAND 1 MAND 2 (Hexadecitnai) (Hexadecimal) (Hexadecsmai)(Hexadecitnai)
32. Tune Command m 01 ~7D 0 0 mainsub/TuneBand
33. Channel Add/Del m b 0 ~ 1
34. Key m c Key code
Owner’s Manual 37