Sony STR-DE635 User Manual
Fm stereo fm-am receiver, Str-de635
Table of contents
Document Outline
- FM Stereo FM-AM Receiver
- Precautions
- Unpacking
- Inserting batteries into the remote
- Before you get started
- Assembling the supplied FM antenna
- Notes on antenna hookups
- Jacks for connecting audio components
- Note on audio component hookups
- Jacks for connecting video components
- Note on video component hookups
- Required cords
- Example of LD player connected via an RF demodulator
- c
- Example of a DVD player hookup using the 5.1 INPUT jacks
- c
- i
- Required cords
- CONTROL A1 II hookup
- Connecting the AC power cord
- Brief descriptions of buttons and control used to set up the speaker system
- Speaker System Hookup
- Performing Initial Setup Operations
- Multi Channel Surround Setup
- Specifying the speaker parameters
- 1 Press l/c!) to turn on the receiver.
- 2 Press SET UP.
- 3 Press the cursor buttons (< or »to select the parameter you want to adjust.
- 4 Turn the jog dial to select setting you desire. The setting is entered automatically.
- 5 Repeat steps 3 and 4 until you have set all of the parameters that follow.
- ■ Front speaker size (FRONT)
- Note
- ■ Center speaker size (CENTER)
- ■ Rear speaker size (REAR)
- ■ Rear speaker position (REAR PL.)*
- Multi Channel Surround Setup
- Adjusting the speaker volume
- Note
- 1 Press l/(!) to turn on the receiver.
- 2 Press TEST TONE on the supplied remote.
- 3 Adjust the volume level so that the volume of the test tone from each speaker sounds the same when you are in your main listening position.
- 4 Press TEST TONE on the remote again to turn off the test tone.
- Notes
- Q You can adjust the volume level of all speakers at the same time
- Specifying the speaker parameters
- Before You Use Your Receiver
- Location of Parts and Basic Operations
- {2\ Function buttons
- [4] 5.1CH INPUT button
- d] MASTER VOLUME control
- [g MUTING button
- [3 SPEAKERS selector
- PHONES jack
- Front Panel Parts Description
- I
- I
- [H DIMMER button
- A.F.D. button / indicator
- MODE button / indicator
- 2CH button / indicator
- И MULTI CHANNEL DECODING indicator
- H BASS BOOST button
- gi EQUALIZER button
- DIRECT button
- SHIFT button
- Numeric buttons (1 to 0)
- AM button
- FM button
- FM MODE button
- MEMORY button
- TUNING -b/- buttons
- PRESET +/- buttons
- 0 LEVEL button
- 521 SUR button
- 51 EQ button
- 51 Cursor buttons ()
- ^ Jog dial
- I NAME button
- I ENTER button
- Enjoying
- Surround
- Sound
- A.F.D.
- c
- c
- c
- a
- Selecting a Sound Field
- Understanding the Multi-Channel Surround Displays
- Customizing Sound Fields
- To get the most from multi channel surround sound
- Adjusting the surround parameters
- Adjusting the level parameters
- 1 Start playing a program source encoded with multi channel surround sound.
- 3 Press the cursor buttons (< or »to select the parameter you want to adjust.
- 4 Turn the jog dial to select setting you desire. The setting is entered automatically.
- Front balance (FRONT)
- Rear balance (REAR)
- Rear level (REAR)
- Center level (CENTER)
- Sub woofer level (SUB WOOFER)
- LFE (Low Frequency Effect) mix level (LFE MIX)
- Dynamic range compressor (D. RANGE COMP)
- Adjusting the equalizer
- 1 Start playing a program source encoded with multi channel surround sound.
- 2 Press EQ.
- 3 Press the cursor buttons (<°r »to select the parameter you want to adjust.
- 4 Turn the jog dial to select setting you desire. The setting is entered automatically.
- 9 You can turn off the equalization without erasing it
- Resetting customized sound fields to the factory settings
- Adjustable parameters for each sound field
- Adjustable parameters for each sound field (continued)
- Receiving
- Broadcasts
- Direct Tuning
- Automatic Tuning
- Preset Tuning
- Direct Tuning
- Brief descriptions of buttons used to receive broadcasts
- 1 Press TUNER to light the button up.
- 2 Press FM or AM to select the FM or AM band.
- 3 Press DIRECT.
- 4 Press the numeric buttons to enter the frequency.
- If you cannot tune in a station and the entered numbers flash
- 5 If you've tuned in an AM station, adjust the direction of the AM loop antenna for optimum reception.
- 6 Repeat Steps 2 to 5 to receive another station.
- 1 Press TUNER to light the button up.
- 2 Press FM or AM to select the FM or AM band.
- 3 Press TUNING + or TUNING -.
- Presetting radio stations
- 1 Press TUNER to light the button up.
- When the receiver reaches either end of the band
- 4 To continue scanning, press TUNING -i- or TUNING - again.
- Tune in the station that you want to preset using Direct Tuning (page 40), or Automatic Tuning (this page).
- Press MEMORY.
- Press SHIFT to select a memory page (A, B or C).
- Select a preset number by pressing it (0 to 9).
- 6 Press MEMORY again to store the station.
- 7 Repeat Steps 2 to 6 to preset another station.
- To change a preset number to another station
- Preset Timing
- Timing to preset stations
- Brief descriptions of buttons used to receive broadcasts
- other
- Operations
- Brief descriptions of buttons that appear in this chapter
- Naming Preset Stations and Program Sources
- 1 To index a preset station
- Press TUNER.
- To index a program source
- Select the program source (component) to be
- named, then go to Step 3.
- 2 Tune in the preset station you want to create an index name for.
- 3 Press NAME.
- 4 Create an index name by using the jog dial and cursor buttons:
- To insert a space
- If you've made a mistake
- 5 Press ENTER.
- To assign index names to other stations
- Recording
- Using the Sleep Tinner
- Recording on a video tape
- 1 Select the program source to be recorded.
- 2 Prepare the component for playing.
- 3 Insert a blank video tape into the VCR (VIDEO 1 or VIDEO 2) for recording.
- 4 Start recording on the recording VCR, then start playing the video tape or laser disc you want to record.
- Press SLEEP on the remote while the power is on.
- Recording on a video tape
- Adjustment Using the SET UP Button
- Troubleshooting
- Specifications
- Tables of Settings Using SUR, LEVEL, EQ, and SET UP buttons
- Index
- Operations