Great Plains 2N-3020 Parts Manual - Manual (Page 77)

Revision Comments Part Description Part No. Ref.
Image No. dwg14453
Rev. 2 CHAIN RL #40 126 PITCHES 136-112D 1.
Use existing stock; rev. 1 RPBY 136-112D 809-153C 1.
Rev. 2 SPKT 40B19X1 B MAX .875 THRU 808-125C 2.
Use existing stock; rev. 1 REPLACED BY 808-125C 152-312D 2.
Rev. 2 JAW CLUTCH CCW EXTENDED 176-041S 3.
Use existing stock; rev. 1 RPBY 176-041S & 176-045S 176-039S 3.
Used only with old clutch 176-039S 36'& 45' SPROCKET SPACER 172-330D 4.
RPBY 808-240C 152-283D 5.
HHCS 1/4-20X1 GR5 802-005C 6.
WASHER LOCK SPRING 3/8 PLT 804-013C 7.
NUT HEX 3/8-16 PLT 803-014C 8.
KEY 1/4 X 1 123-004D 9.
GAUGE WHEEL JACK SHAFT 152-266D 10.
HHCS 1/2-13X1 GR5 802-258C 11.
PIN COTTER 7/64 X 1 LONG 805-064C 12.
WASHER FLAT 1/2 SAE PLT 804-016C 13.
IDLER ROLLER 195-069D 14.
TWO PIN IDLER WELDMENT 120-212H 15.
BRG CUP 3.67ODX.93WD #3720 822-037C 16.
BRG CONE 2.00IDX1.18WD #3780 822-036C 17.
SEAL DBL LIP 2.5 ID X 3.881 OD 816-138C 18.
RPBY 152-191A 152-271D 19.
RPBY 152-191A 152-270D 19.
BUSHING WALKING TANDEM 890-133C 20.
PIN ROLL 3/8 X 3 1/2 PLT 805-116C 21.
RPBY 152-191A 152-267D 22.
SPRING COMP 1/2 OD X 1 LG 807-096C 23.
RPBY 152-191A 152-268D 24.
RPBY 152-191A 152-272D 25.
KEY 1/4 X 11/16 LONG 310-331D 26.
PIN ROLL 5/16 X 2 1/2 PLT 805-125C 27.
Rev. 2 SPKT 40B23 X 2 W/5/16 HOLE 808-059C 28.
Use existing stock; rev. 1 RPBY 808-059C 152-311D 28.
RPBY 152-268S 152-133H 29.
SEAL 2 X 3.1875 X 0.469 816-084C 30.
RPBY 152-191A 152-274D 31.
RPBY 152-191A 152-269D 32.
WASHER BRG TONGUED K91509 804-106C 33.
WASHER BRG LOCK 1.767 804-083C 34.
NUT BRG LOCK 1.767 OD THD 803-186C 35.
Rev. 2 CHAIN RL #40 140 PITCHES 136-116D 36.
Use existing stock; rev. 1 RPBY 136-116D 809-158C 36.
NUT HEX JAM 5/8-11 PLT 803-023C 37.
SCREW SQ HD 5/8-11X3 1/2 GR5 801-059C 38.
HHCS 3/8-16X1 GR5 802-017C 39.
PIN ROLL 7/32 X 3 PLT 805-211C 40.
NUT LOCK 1/2-13 PLT 803-019C 41.
IDLER ARM RETAINER 152-372D 42.
CLUTCH ENGAGE ARM 152-262D 43.
PIN ROLL 3/16X 1 1/2 PLT 805-024C 44.
CLUTCH ENGAGEMENT BRACKET 152-376D 45.
WASHER FLAT 1/4 SAE PLT 804-007C 46.
WASHER LOCK SPRING 1/4 PLT 804-006C 47.
04/09/13 - 77 - 196-164P
Table of Contents Part Number Index
Drive
Gauge Wheel Drive (S/N C1692- 24' Drills And D1904- 30' Drills)
(Applies to 2N-2420 (1995+), 2N-3020 (1995+) only)