Great Plains 2N-3010 Parts Manual - Manual (Page 71)

Revision Comments Part Description Part No. Ref.
Image No. dwg16044
2nd rev. CHAIN RL #40 126 PITCHES 136-112D 1.
Use existing stock; 1st rev. RPBY 136-112D 809-153C 1.
SPKT 40B19X1 B MAX .875 THRU 808-125C 2.
JAW CLUTCH CCW EXTENDED 176-041S 3.
RPBY 808-240C 152-283D 4.
HHCS 1/4-20X3/4 GR5 802-004C 5.
WASHER LOCK SPRING 3/8 PLT 804-013C 6.
NUT HEX 3/8-16 PLT 803-014C 7.
KEY 1/4 X 1 123-004D 8.
GAUGE WHEEL JACK SHAFT 152-266D 9.
HHCS 1/2-13X1 GR5 802-258C 10.
PIN COTTER 7/64 X 1 LONG 805-064C 11.
WASHER FLAT 1/2 SAE PLT 804-016C 12.
3rd rev. RPBY 817-713C 817-333C 13.
Use existing stock; 2nd rev. Use with item 42. IDLER BUSHING 404-033D 13.
Use existing stock; 1st rev. IDLER ROLLER 195-069D 13.
TWO PIN IDLER WELDMENT 120-212H 14.
BRG CUP 3.67ODX.93WD #3720 822-037C 15.
BRG CONE 2.00IDX1.18WD #3780 822-036C 16.
SEAL DBL LIP 2.5 ID X 3.881 OD 816-138C 17.
NUT BRG LOCK, TN-10 803-208C 18.
WASHER BRG LOCK, TW110 804-098C 19.
NUT HEX FLANGE LOCK 5/8-11 PLT 803-263C 20.
WASHER FLAT 5/8 HARD ASTMF436 804-095C 21.
6-BOLT HEAVY DRIVE HUB 2 BORE 152-390D 22.
RPBY 802-687C 802-640C 23.
SPNDLE 2'"X22 5/16W/1.95-18THD 152-387D 24.
AXLE SPACER TUBE 120-198D 25.
PIN ROLL 5/16 X 2 1/2 PLT 805-125C 26.
SPKT 40B23 X 2 W/5/16 HOLE 808-059C 27.
2SNT GAUGE WHEEL WELDMENT 152-190H 28.
SEAL 2 X 3.1875 X 0.469 816-084C 29.
2nd rev. CHAIN RL #40 140 PITCHES 136-116D 30.
Use existing stock; 1st rev. RPBY 136-116D 809-158C 30.
NUT HEX JAM 5/8-11 PLT 803-023C 31.
SCREW SQ HD 5/8-11X3 1/2 GR5 801-059C 32.
HHCS 3/8-16X1 GR5 802-017C 33.
NUT LOCK 1/2-13 PLT 803-019C 34.
IDLER ARM RETAINER 152-372D 35.
CLUTCH ENGAGE ARM 152-262D 36.
PIN ROLL 3/16X 1 1/2 PLT 805-024C 37.
CLUTCH ENGAGEMENT BRACKET 152-376D 38.
WASHER LOCK SPRING 1/4 PLT 804-006C 39.
PIN ROLL 1/4 X 3/4 PLT 805-026C 40.
Includes items 17 through 25 & 29 2SNT SOLID GAUGE WHEEL UPDATE 152-191A 41.
GW IDLER SPACER 152-411D 42.
01/31/14 - 71 - 196-126P Rev. A
Table of Contents Part Number Index
Drives
Gauge Wheel Drive (S/N C1693- C1851 24' Drills And S/N D1905- D2183 30'
Drills)
(Applies to 2N-2410 (1995+), 2N-3010 (1995+) only)