Quoizel ER353BN Emery User Manual
Page 2
2of3
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at
2014 QuoizelInc.
March2014
STEP 3
Install Fixture Chains
-
*
A. Adjust the Fixture Chain (CC) to your
desired length by removing the links if
needed.
Pliers is required for this step.
B. With the Fixture Chain (CC) not
attached to the Fixture Loop (A) and
the Canopy Chain Loop, pull the
supply wires through the Fixture Chain
(CC) alternating links. After the wires
are through the Fixture Chain (CC),
pull the Supply Wires and the Ground
Wire through the Ceiling Canopy (BB).
C. Attach one ends of the Fixture Chains
(CC) to the Fixture Loop (A) with two
Figure 8
BB
DD
CC
DD
A
Ceiling
Loop
Quick Links (DD) as shown. Lift the fixture and Fixture Chains (CC)
up and attach the other ends of the Fixture Chains (CC) onto the
Canopy Chain Loop underside of the Ceiling Canopy (BB) with the
rest two Quick Links (DD).
Suggested rods and chain length for Ceiling height :
8
’ ceiling : use (1)6” rod and 2 quick links
9
’ ceiling : use (1)12” rod, 5 links of chain and 2 quick links
10
’ ceiling : use (2)12” rods, 5 links of chain and 2 quick links
Supply
Wires
Figure 4
STEP 4
Separate parts from Crossbar Assembly
-
A. Remove the Finial, the Covers, and the Lock Washer from the
Crossbar Assembly (AA).
Nipple
Lock Washer
Cover A
Cover B
Finial
AA
STEP 5
Install Crossbar
-
A.
AA)
Attach the Crossbar (
to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included)
Tighten until snug
.
.
Figure 5
Outlet Box
Outlet Box Screw
(not included)
Green
Ground Screw
AA
from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
side Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 7
STEP 7
Install Ceiling Canopy
-
A. Attach the Lock Washer, the Ceiling
Canopy (BB) and the Covers over the
end of the Nipple as shown. Secure
by threading the Finial onto the
Nipple. Hand tighten until snug.
Finial
Cover B
Cover A
BB
Nipple
Lock Washer
E
F
G
D
Socket
STEP 8
Install Shade
-
A. Place the Upper Collar (D), the Shade (E)
and the Steel Collar (F) in turn and secure
with the Harp with Socket Collar (G). Hand
tighten until snug.
Figure 9
STEP 9
Install Bulb
-
A. This fixture uses standard bulb with
medium base. Maximum 100 watts.
B. Insert bulb and screw snugly into place.
Bulb
STEP 10
Install Diffuser
-
A. Thread one Hex Nut (K) to the Nipple
(H) approx half way. Screw the Nipple
(H) into the bottom end of the Harp (G)
and tighten until snug. By using pliers,
thread the Hex Nut (K) against the Harp
(G) and hand tighten until snug.
B. Thread another Hex Nut (K) onto the
end of the Nipple (H) and adjust it to
proper location for rest components.
Attach the Flat Washer (I), the Rubber
Washer (J), the Diffuser (L) and the
Small Flat Washer (M) over the Nipple
(H) in turn. Secure them with the Finial
(N) and hand tighten until snug.
Your fixture is now assembled and ready
to use. Enjoy!
G
H
Figure 10
STEP 6 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire
White wire
from supply
Ribbed side wire
from fixture
Black wire from
supply (or Red)
Smooth side wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 6
K
K
I
J
L
M
N