Quoizel GE5009SE Genova - Manual

FIXTURE CANOPY
CENTER STEM
UPPER ROD
LOWER ROD
UPPER
JUNCTION
BODY
SMALL LOOP
LOWER
JUNCTION BODY
SHADE
HOLDER
SOCKET
SHADE
SOCKET
COLLAR
CONNECTOR
WHEEL PART
FINIAL
FIGURE1
ASSEMBLY / INSTALLATION INSTRUCTIONS
1.Before beginning fixture fabrication, carefully unpack
all parts referring to illustration FIGURE1 for parts
identification.
2.Turn power to the installation point OFF at circuit
breaker.
3.Thread the end of CENTER STEM onto nippple on the
top center of UPPER JUNCTION BODY. Hand tighten
until snug. Locate top ends of UPPER RODS through
the holes on the side of FIXTURE COVER and thread
KNOBS onto the ends. Proceed to thread the nipple
in the bottom center of FIXTURE CANOPY into HEX
COUPLING in the center of FIXTURE COVER. Hand
tighten until snug. Then thread FIXTURE LOOP onto
the nipple on the top center of FIXTURE CANOPY
and tighten until snug.
4.Thread NIPPLE into CONNECTOR underside of
LOWER JUNCTION BODY. Hand tighten until snug.
Proceed to locate WHEEL PART over the nipple and
thread FINIAL onto the nipple until snug to secure it.
5.Thread ends of LOWER RODS into SMALL LOOPS
on LOWER JUNCTION BODY. Hand tighten until snug.
Proceed to thread ends of UPPER RODS into top
ends of LOWER RODS. Hand tighten until snug.
6.(For Canadian installation, please refer to Page2)
Fasten the CROSSBAR to the OUTLET BOX with
(2)OUTLET BOX SCREWS(not supplied). Proceed to
thread LOCK NUT A and SHAKE PROOF WASHER A
onto the top end of NIPPLE. Thread NIPPLE into the
center of CROSSBAR. Locate the LOCK NUT B onto the
bottom end of the NIPPLE. Tighten LOCK NUT A against
CROSSBAR with plier until snug.
7. Locate the FIXTURE CHAIN and determine desired
hanging height of fixture. Adjust chain by removing links
if needed. Please note that depending on chain material
thickness, you might be required to use chain pliers to
spread links open. Proceed to attach one end of chain to
FIXTURE LOOP, attached to top of fixture. Pass the
fixture wires through FIXTURE CHAIN alternating links.
Proceed to pass the fixture wires through the following
mounting components in this order: 1)CANOPY LOCK
RING; 2)LOWER CEILING CANOPY; 3)UPPER CEILING
CANOPY; 4) CANOPY CHAIN LOOP; 5) SHAKE PROOF
WASHER B.
8. Making the connections:(2 people recommended for
the remaining steps) Position the fixture under the ceiling
mounted outlet box. Pass SHAKE PROOF WASHER B
over the NIPPLE. Thread CANOPY CHAIN LOOP onto
NIPPLE. Thread LOCK NUT B down the NIPPLE,
against the CANOPY CHAIN LOOP and snug with pliers.
Pass the wires through the NIPPLE. Take up wire slack
and trim wires so that approx. 6” will remain inside outlet
box. Proceed to attach the top of the FIXTURE CHAIN to
the bottom of the CANOPY CHAIN LOOP. Using wire
connectors(not supplied) connect the HOUSE GROUND
WIRE to the FIXTURE GROUND WIRE; connect the
HOUSE WHITE WIRE to the FIXTURE SUPPLY WIRE
(WHITE or RIBBED SIDE); connect the HOUSE BLACK
(or RED) WIRE to the FIXTURE SUPPLY WIRE(BLACK
or SMOOTH SIDE). Wrap each connection with approved
electrical tape.
9. With the proper connections made, proceed to push the
LOWER CEILING CANOPY with UPPER CEILING
CANOPY upward over the OUTLET BOX. Be sure that all
wires are carefully tucked into the OUTLET BOX cavity.
Secure canopies against ceiling by threading CANOPY
LOCK RING onto the CANOPY LOOP. Tighten until snug.
10.Locate SHADES over SOCKETS onto SHADE
HOLDERS. Secure by threading SOCKET COLLARS
onto SOCKETS and tighten until snug. Install bulbs
referring to fixture markings and/or labels for
maximum wattage.
11.Restore power to the installation point ON. Retain this
sheet for future reference.
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN!
IS-GE5009
Page 1 of 3
12.05
OUTLET BOX
HOUSE SUPPLY and
GROUND WIRES
OUTLET BOX SCREWS
(not supplied)
GREEN GROUND SCREW
CROSSBAR
SHAKE PROOF
WASHER A
LOCK NUT A
NIPPLE
LOCK NUT B
SHAKE PROOF
WASHER B
CANOPY CHAIN LOOP
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE CHAIN
UPPER CEILING
CANOPY
CANOPY LOCK RING
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE LOOP
LOWER CEILING
CANOPY
KNOB
FIXTURE COVER
HEX COUPLING
NIPPLE
6 CORPORATE PARKWAY
GOOSE CREEK, SC. 29445
www. quoizel. com