Weller WESD51 - Manual (Page 2)

SPECIFICATIONS
STATIONS
1. Power Input: 120VAC ±10%, 60 Hz, (230VAC ±10%, 50/60 Hz), 60 watts.
2. Power unit output voltage: Isolated 24VAC @ 2.1 amperes.
3. Size: 4.5" x 5.9" x 3.6".
4. Line Cord: 3-Wire
5. Tip temperature control range: 350°F to 850°F (177°C to 454° C).
6. Control setting resolution: 1° F (1° C).
7. Stability: ±10° F (±6° C) per MIL-STD-2000.
8. Absolute accuracy: Average tip temperature can be “Offset” to ±9° F (±5° C) at idle with no load.
9. Ambient temperature range: 60° F to 110° F (16° C to 44° C).
IRONS
1. Wattage: 50 watts at 24 VAC.
2. Tip voltage: Less than 2 mv TRMS to line cord ground pin.
3. Tool weight: 2 ounces without cord.
4. Tool material: Static dissipative thermoplastic handle and stainless steel.
5. Heater type: Fiberglass and ceramic insulated heating element. Reverse wound for low leakage and magnetic
field cancellation.
6. Tip type: Weller ® ET and SMT series tips. Copper with heavy Iron, Nickel and Chromium plating for long
life.
7. Sensor: Type “K” Thermocouple. Fits deep inside tip for maximum response.
8. Handle design: Heat insulated with foam sleeve for low grip temperature and maximum comfort.
9. Tool cord: Silicone rubber, burn resistant.
10. Connector: Polarized, 6 pin locking.
11. Recovery time: Less than 10 seconds from 100°F drop with ETA tip at 700°F.
STANDARDS
1. Housing and tool handle made with Electrostatic Protective Materials as required in MIL-B-81705.
2. Housing passes Static Decay Test per Federal Test Method Std. No. 101, Method 4046.
3. Weller
® ESD tools comply with DOD-HDBK-263.
4. WES51 & WESD51 units meet MIL-STD-2000, MIL-S-45743, W-S-6536, W-S-570 and DOD-STD-1686.
5. WESD51 units meet all applicable standards for CE mark.
ACTIVATION OF LOCKOUT FEATURE
1. Set the digital display to the desired tip temperature.
2. Momentarily touch the Lockout Pencil (PW50) to the ESD symbol on the front panel. The decimal point on the MSD (Most
Significant Digit) will blink if the Lockout Pencil is held against the touch panel. Remove the Lockout Pencil from the ESD
Symbol and the single decimal point in the MSD (Most Significant Digit) will be illuminated, indicating that the station has
been “Locked”. The lockout set temperature will be displayed for 3 seconds before switching to the actual tip tempera-
ture. Adjusting the temperature set knob will temporarily display the “Set” point of the station, even though the unit will
not change the temperature setting, when in the “Lockout” mode.
3. Reverse the lockout by momentarily touching the Lockout Pencil to the ESD symbol. Remove the Lockout Pencil slowly
and the temperature set knob will function as normal. The single decimal point in the MSD (Most Significant Digit) will
now be “Off”.
Note: If the temperature set knob is adjusted during the “Lockout” mode, the temperature setting will display the
current “Position/Setting” of the temperature set pot, when the “Lockout” function is removed.
TIP TEMPERATURE “OFFSET” PROCEDURE
1. Monitor the tip temperature using the K111, Type “K” Thermocoupled Tip temperature test kits. (see Replacement Parts
and Accessories Section)
2. Set the digital display to the desired tip temperature and allow the tip temperature to stabilize (as indicated by the “Read”
mode).
2