Stealth Cam STC-U732K UNIT-7 User Manual

Page 5

WWW.STEALTHCAM.NET
Toll Free 877-269-8490

Setting the Capturing Sequence in PIR operation mode:

Your Stealth Cam can be programmed to shoot 1‐9 pictures per
triggering.

• Switch the camera to the ON position.

¾ LCD screen will display the camera status screen.

• Press the [MENU] button once within 30 seconds to enter the

programming mode.

• The word PIR will be blinking, press OK to confirm the camera

operation by PIR detection.

• Press the [UP] button ONE time to enter the Capturing Sequence

setting mode.

• The word CAMERA will be blinking.
• Press [OK] button and the current number of burst mode images

will blink.

• Press the [UP] or [DN] button to select the desired burst mode

setting or number of pictures per triggering.

• Press [OK] to save your selection.
• Press [MENU] button to exit.

WWW.STEALTHCAM.NET
Toll Free 877-269-8490

Setting the Video Mode in PIR operation mode:

Your Stealth Cam can be programmed to record 10‐180 seconds of
video per triggering. The Video mode is only workable under PIR
mode.

• Switch the camera to the ON position.

¾ LCD screen will display the camera status screen.

• Press the [MENU] button once within 30 seconds to enter the

programming mode.

• The word PIR will be blinking, press OK to confirm the camera

operation by PIR detection.

• Press [UP] button TWO times to enter Video setting mode.
• The word VIDEO will be blinking.
• Press [OK] button and the video length in seconds will be blinking.
• Press [UP] or [DN] button to select the desired video length from

10 to 180 seconds in 5 second increments.

• Press [OK] to save your selection.
• Press [MENU] button to exit.

WWW.STEALTHCAM.NET
Toll Free 877-269-8490

Set the Digital Zoom in PIR operation mode:

Your Stealth Cam can be programmed to have 3 different zoom levels.

• Switch the camera to the ON position.

¾ LCD screen will display the camera status screen.

• Press the [MENU] button once within 30 seconds to enter the

programming mode.

• The word PIR will be blinking, press OK to confirm the camera

operation by PIR detection.

• Press [UP] button THREE times to enter Zoom setting mode.
• The word ZOOM will be blinking.
• Press [OK] button and the zoom level number will now blink.
• Press the [UP] or [DN] button to select the desired zoom level

setting 1 (1X Normal) / 2 (2X Zoom) / 4 (4X Zoom).

• Press [OK] to confirm your selection
• Press [MENU] button to exit.

NOTE: The use of the digital zoom feature may degrade image &
video quality, as this tells the camera to focus on a specific are of the
image and increase its size. This will cause dithering of the image.

WWW.STEALTHCAM.NET
Toll Free 877-269-8490

Setting the Time Out Mode in PIR operation mode:

Your Stealth Cam can be programmed to set the amount of time in
seconds or minutes the camera will sleep between PIR triggers.

• Switch the camera to the ON position.

¾ LCD screen will display the camera status screen.

• Press the [MENU] button once within 30 seconds to enter the

programming mode.

• The word PIR will be blinking, press [OK] to confirm the camera

operation by PIR detection.

• Press [UP] button FOUR times to enter Time Out setting mode.
• The word TIME OUT will be blinking.

• Press [OK] button and the SECONDS digits will be blinking.
• Press [UP] or [DN] button to increase or decrease the time value

in seconds from 0 to 59 seconds in 1 second increments.

• Press [OK] to save the seconds setting and the MINUTES digits will

be blinking.

• Press [UP] or [DN] button to increase or decrease the time value

in minutes from 0 to 59 minutes in 1 minute increments.

• Press [OK] to save the minutes setting.
• You’ll then see the word ‐ TIME ‐ blinking.
• Press [MENU] button to exit.