Rite-Ride 2535 - Manual

2535
08-14
INSTALLATION INSTRUCTIONS
Congratulations—your new Air Helper Springs are quality
products capable of improving the handling and comfort
of your vehicle. As with all products, proper installation is
the key to obtaining all of the benefits your kit is capable
of delivering. Please take a few minutes to read through
the instructions to identify the components and learn
where and how they are used. It is a good idea to start by
comparing the parts in your kit with the parts list below.
The heart of the air helper spring kit is, of course, the
air springs. Remember that the air helper springs must
flex and expand during operation, so be sure that there
is enough clearance to do so without rubbing against any
other part of the vehicle.
Be sure to take all applicable safety precautions
during the installation of the kit. The instructions listed
in this brochure and the illustrations all show the left,
or driver’s side of the vehicle. To install the right side
assembly simply follow the same procedures.
Your kit includes separate inflation valves and air
lines for each air helper spring. This will allow you to
level your vehicle from side to side as well as from front
to back. If you would rather have a single valve inflation
system, your dealer can supply the optional “T” fitting.
IMPORTANT!
For your safety and to prevent possible damage
to your vehicle, do not exceed the maximum load
recommended by the vehicle manufacturer (GVWR).
Although your Air Helper Springs are rated at a maximum
inflation pressure of 100 psi, this pressure may allow you
to carry too great a load on some vehicles. It is best to
have your vehicle weighed once it is completely loaded
and compare that weight to the maximum allowed. Check
your vehicle owner’s manual or data plate on driver’s side
door for maximum loads listed for your vehicle.
When inflating your Air Helper Springs, add air pres-
sure in small quantities, checking pressure frequently
during inflation. The air spring requires much less air
volume than a tire and, therefore, inflates much quicker.
Remove the negative battery cable. It is not neces-
sary to jack up the truck to install this Ride-Rite kit, if you
DO, please use chocks in front of the front tires. Also,
use jack stands beneath the truck’s rear axle that are
properly rated to support the trucks weight.
WARNING:
Do not inflate this assembly when it is
unrestricted. The assembly must be restricted
by the suspension or other adequate structure.
Do not inflate beyond 100 psi. Improper use or
over inflation may cause property damage or
severe personal injury.
The air springs in this kit have a
minimum pressure of 5 psi and maximum
of 100 psi after the truck is loaded.
224C AIR SPRING 6401 2
RIGHT UPPER BRACKET 5572 1
LEFT UPPER BRACKET 5717 1
LOWER BRACKET 5726 2
SADDLE BRACKET 5379 2
BRACKET STRAP 1163 2
1/2" SPACER 5477 2
BAIL CLAMP 3077 2
HEAT SHIELD 1004 2
AIR LINE TUBING 1
3/8"-16 X 1-1/2" HEX HEAD BOLT 1
3/8" FLAT WASHER 1
5/16" FLAT WASHER 4
3/8"-16 X 3/4" HEX HEAD BOLT 2
3/8"-16 X 1" HEX HEAD BOLT 8
3/8"-16 X 2 1/2" FLAT HEAD BOLT 2
3/8"-16 FLANGE LOCK NUT 19
3/8" LARGE FLAT WASHER 2
3/8"-16 X 3" CARRIAGE BOLT 4
3/4"-16 X 1-3/4" HEX HEAD BOLT 1
3/4"-16 HEX NUT 2
3/4"-16 FRAME NUT 3412 1
3/4" INTERNAL TOOTH LOCK WASHER 2
3/4" THICK FLAT WASHER 1
3/4" FLAT WASHER 1
3/4" LOCK WASHER 2
INFLATION VALVE 3032 2
STRAIGHT FITTING 3046 2
THERMAL SLEEVE 2
NYLON TIE 6
CAUTION TAG 2
PARTS LIST
DO NOT INSTALL if the truck has been lifted and
the stock jounce bumper spacers are not on the
vehicle.
HARDWARE PACK (A21-760-2535)