Nipros ES-500P System Connection Manual - Manual (Page 4)

(rear)
Turns when POWER switch is on.
Connect with the AC 85V-240V (50/60Hz)
power supply.
CAMERA AUDIO OUT EXT LINE (2W I/O) EXT LINE (2W I/O)
HD/SD COMPONENT OUT VIDEO OUT VIDEO IN AUX
ZOOM
TC OUT FOCUS IRIS
SDI IN OUT 1 OUT 2 OUT 1 OUT 2 SDI RET IN
TC IN RET IN
TALLY EXT LINE (4W I/O)
IN OUT
Y Pb Pr
AC IN
HD/SD COMPONENT OUT Y/Pb/Pr
Output the HD/SD analog component signal,
Y, Pb and Pr from ES-500P.
AUDIO OUT connector
Outputs the audio signal from
ES-500P.
EXT LINE (2W I/O) connectors
Connect to an external
2-wire intercom line.
1 GND
2 HOT
3 COLD
1 GND
2 NC
3 INCOM H
ZOOM connector
Connect to an ZOOM remote controller with the cable
supplied with the remote controller.
REMOTE connector
Connect to the camera manufacturer’s remote controller
with the cable supplied with the remote controller.
Do not connect and use the ZOOM connector and/or the
FOCUS IRIS connector when using the REMOTE connector.
Do not connect and use the REMOTE connector when using
the ZOOM connector and/or the FOCUS IRIS connector.
TALLY EXT LINE (4W I/O) IN/OUT
Used for the tally signal input/output and
for the connection to an external 4-wire intercom line.
Input the time code signal.
Input the composite video return signal from a switcher.
Input the FOCUS IRIS signal to the camera connected to
ES-500P.
AUX connector
and VIDEO IN/TC OUT select switch
Input the composite video signal from an external equipment
or outputs the time cord signal from ES-500P.
Select the VIDEO IN or the TC OUT by the select switch.
Input the HD/SD-SDI signal from a camera.
Output the HD/SD-SDI signal
(through output of the SDI IN input signal).
Outputs the composite video signal from ES-500P.
Input the HD/SD-SDI return signal
from a switcher.
Output the HD/SD-SDI return signal
(through output of the SDI RET IN input signal).
1 TALLY 1
2 TALLY 2
3 TALLY 3
4 TALLY 4
5 TALLY 5 11 4W OUT H
12 4W OUT L
13 4W IN H
14 4W IN L
15 GND 6 NC
7 NC
8 NC
9 NC
10 GND
Do not connect and use the REMOTE connector when using
the FOCUS IRIS connector and/or the ZOOM connector.
CAMERA connector
Connect to ES-500P with a 26-pin multi-cable,
NIPROS ESC-10/25/50.
1 VIDEO IN
2 VIDEO SG
3 Y SG
4 Y IN
5 R-Y IN
6 R-Y SG
7 B-Y IN
8 B-Y SG
9 MIC X IN 10 MIC Y IN
11 MIC G
12 REM TX X
13 REM VIDEO X
14 REM POW(NC)
15 TALLY OUT
16 GEN OUT G
17 REM VIDEO G
18 RET V OUT 19 RET V OUT G
20 INCOM
21 GEN OUT X
22 REM TX Y
23 REM RX X
24 REM RX Y
A +12V
B GND
SDI IN
SDI OUT 1/2
SDI RET IN
SDI RET OUT 1/2
(BNC)
(BNC)
(BNC×2)
(BNC×2)
(BNC×3)
(3.5 φ Mini jack)
VIDEO OUT (BNC)
(BNC)
FOCUS IRIS
RET IN (BNC)
TC IN (BNC)
(HD D-sub 15-pin, female)
FAN
AC IN
(XLR 3-pin, female and male)
(XLR 3-pin, male)
(26-pin, female)
(φ2.5 mini-jack)
ES-600P/ES-500P : for Panasonic camera
ES-600P/ES-500P incorporates the REMOTE connector
according to the Panasonic cameraremote controller.
ES-600P Outsideview / Parts Names and Functions (Rear panel)
NOTICE : ES-600P and ES-500P do not convert the media or format of the input signals to annother.
2
NOTE : The video signal from ES-500P cannot be output
to the REMOTE connector of ES-600P,
but to the VIDEO OUT connector of ES-600P.