beautypg.com

Nipros ST-7 User Manual

St-7, Power

background image

For using

ST-7.

Please read this manual thoroughly before operating the unit.

■Outsideview and Dimensions

4. Install a lithium-ion battery to the rear of

ST-7.

6. Conversion cables which are supplied to

a camera can be connected with the BNC-

BNC relay connector.

7. ST-7 can be installed to the Sony tripod base

VCT-14/U14 to install to a tripod.

5. Turn on the POWER SW on the bottom of the

rear of ST-7. LED indicator lights up and the

power is supplied to a camera and a light.

ST-7

Shoulder Adaptor

■ DC OUT CONNECTOR

1

2
3
4

DC12V(G)
DC8.4V(G)
DC8.4V(+)
DC12V(+)

POWER

OFF

ON

Operating

Instructions

■ Caution : They might damage the grip portion of a camera if you lift a camera up with

only the grip portion or install a receiver of the wireless microphone, a hard disk back

up unit, etc. to the battery shoe of ST-7.

A small camera applicable to ST-7 is designed to be used as it is. We recommend

you to use ST-7 as a support equipment. It is not applied to the operation which

gives a big weight pressure to the grip portion and the application to use a wireless

receiver and a hard disk back up unit together.

■ Main Features :

ST-7 is applicable to a handy type camera/camerarecorder.

ST-7 can be installed to the Sony tripod base VCT-14/U14.

To supply a power of +8.4 V

for a camera and a power of

+12 V for a wireless receiver.

■ Operation

1.Install ST-7 to the bottom of a handy

camera with the guide pin. And tighten

the camera screw to fit it to a camera.

ST-7

Spare screw

with washer

Camera screw

with washer

Guide

pin

Camera

screw

Spare

screw

Washer

Camera

screw

Guide pin

plate

ST-7

take off

remove

install

ST-7

Fit the washer

to each screw.

For a camera which has two screw holes

1 Take off the guide pin plate from the ST-7 loosening

the camera screw and remove the camera screw from

the guide pin plate. Fit the washers(supplied) to the

spare screw (supplied) and the camera screw.

2 Install the screws with the washers to the ST-7 and fix

the ST-7 into the screw holes of a camera with the

two screws.

1

2

120

170

449

NIPROS accept no liability whatever for damages arising from improper use not conforming to the

instructions in the instruction manuals.

NIPROS accept no liability whatever for incidental damages arising out of the use or inability to use

the product, including, but not limited to, damage to the camera, etc., corruption or loss of data, lost

business revenue or suspension of business operations.

■Specifications

DC IN DC 12 V XLR 4-pin( Male ) 1
V-shoe mount

(

Li-ion Battery Input) 1

DC OUT DC 12 V XLR 4-pin(Female) 1
DC 12/8.4 V Mini 4-pin(Female) 1
Extension terminal BNC-BNC 3
1/4 in. camera screw 1 with rotation prevention 1
1/4 in. camera screw 1 Spare
Shoulder pad Just fit shoulder pad
Operating temperature 0℃ to +40℃
Storage temperature -20℃ to +60℃
Outside dimensions

120 170 449 mm(W H D)

Weight approx. 1.5 kg

* The protection circuit is equipped

so that the MINI 4-pin(Female)

connector can continue to supply

the power to a camcorder even if

the XLR 4-pin output is shorted

or troubled.


NOTE

Features, design and specifications are subject to change without notice.

TM

2. Fix the handle of ST-7 to the screw hole

on the upper side of the grip of the camera

with the supplied screw.

3. If the power is supplied to a camera from

ST-7, please use the optional DC power cable

according to the camera used.

■ In the case of Sony PMW-EX3,

Press the hook stay on the belt hole at

the rear of the camcorder, and pressing

downward fix the stay with the screw.

Hook stay

Screw