Nipros ES-500P System Connection Manual - Manual (Page 2)

Y IN/Pb IN/Pr IN connectors (BNC×3)
RET OUT connector (BNC)
TALLY OUT connector (BNC)
Connect the HD/SD analog component
signals(Y/ Pb(B-Y)/ Pr(R-Y)) from a
camera.
Outputs the return video signal(composite)
from ES-600P.
Outputs the TALLY signal from ES-600P.
AUX
(VIDEO OUT/TC IN) connector (BNC)
Outputs the composite video signal
connected to the AUX(VIDEO IN) of
ES-600P or input the time cord signal
from a camera.
MONITOR OUT connector (6-pin)
Connect with Monitor LVM-89W or VF
Interface Unit VIF-100 by VF 6-pin cable
(VC-450). The RET composite video
signal, DC 12V power and tally signal are
supplied to LVM-89W or VIF-100.
ZOOM connector (φ2.5 mini jack)
Connects with ZOOM connector of the
camera when using a ZOOM remote
controller connected to ES-600P.
Do not connect and use REMOTE connector when using
ZOOM connector and/or FOCUS IRIS connector.
FOCUS IRIS connector
(φ3.5 stereo mini-jack)
Outputs the FOCUS / IRIS control signal
to a camera, FOCUS IRIS connector.
Do not connect and use REMOTE connector when using
FOCUS IRIS connector and/or ZOOM connector.
* When using Panasonic camera and VIF-100P
connecting to ES-500P, input the return signal,
HD-Y component signal or composite signal,
to RET IN connector of ES-600P according to
the VF input of the camera connected.
VF Interface Unit
1 GND
2 DC +12 V OUT
3 NC
4 RET VIDEO
5 TALLY OUT
6 NC
REMOTE connector
Connects with the remote connector of
the camera by the supplied Remote Cable
RCC-450P when using a camera remote
controller connected to ES-600P.
Do not connect and use ZOOM connector and/or
FOCUS IRIS connector when using REMOTE connector.
ES-500P/ES-600P : for Panasonic camera
ES-500P/ES-600P incorporates the REMOTE connector
according to the Panasonic cameraremote controller.
CAMERA connector (26-pin, male)
Connect with ES-600P by a 26-pin cable
or NIPROS ES Cable, ESC-10/25/50.
1 VIDEO OUT
2 VIDEO SG
3 Y SG
4 Y OUT
5 R-Y OUT
6 R-Y SG
7 B-Y OUT
8 B-Y SG
9 MIC X OUT
10 MIC Y OUT
11 MIC G
12 REM TX X
13 REM VIDEO X
14 REM POW
15 TALLY IN
16 GEN IN G
17 REM VIDEO G
18 RET V IN
19 RET V IN G
20 INCOM
21 GEN IN X
22 REM TX Y
23 REM RX X
24 REM RX Y
A +12V
B GND
INTERCOM HEADSET (XLR 4-pin)
Connects the Intercom headset DL-400.
1 MIC (G)
2 MIC (H)
3 H.PHONE(G)
4 H.PHONE(H)
AUDIO IN connector(XLR 3-pin)
Input the audio signal from a camera.
TC OUT connector (BNC)
Outputs the time code signal from
ES-600P to a camera.
VIDEO IN connector (BNC)
Input the composite video signal from
a camera.
1 GND
2 HOT
3 COLD
VIF-100P : for Panasonic*
(connector panel)
ES-500P Outsideview / Parts Names and Functions (Connector panel)
MONITOR
OUT
TC OUT
Y IN
H S U P
TALLY OUT
RET OUT
MADE IN JAPAN
AUX
Pb IN
Pr IN
FOCUS IRIS
(VIDEO OUT/TC IN)
REMOTE
▲
▲HEADSET
AUDIO IN
▲
VIDEO IN
ZOOM
V-shoe and DC OUT connector
Mount to the V-shoe mount (V-mount
battery holder) on a camera and output
the DC 12 V power to the camera.
NOTICE : ES-500P and ES-600P do not convert the media or format of the input signals to annother.
NOTE : However the video signal from
ES-500P cannot be output to the
REMOTE connector of ES-600P,
but to the VIDEO OUT connector
of ES-600P.
2